Skip to content

Clean Fuel Regulations

SOR/2022-140

In forceCurrent to September 30, 2026 HistoryRegistered on June 21, 2022Made under: Canadian Environmental Protection Act, 1999

Full text

Whereas, under subsection 332(1) Footnote a of the Canadian Environmental Protection Act, 1999 Footnote b, the Minister of the Environment published in the Canada Gazette, Part I, on December 19, 2020, a copy of the proposed Clean Fuel Regulations, substantially in the annexed form, and persons were given an opportunity to file comments with respect to the proposed Regulations or to file a notice of objection requesting that a board of review be established and stating the reasons for the objection;

Whereas the Governor in Council is of the opinion that the proposed Regulations could make a significant contribution to the prevention of, or a reduction in, air pollution resulting, directly or indirectly, from the combustion of liquid fossil fuels;

And whereas, under subsection 140(4) of that Act, before recommending the proposed Regulations, the Minister of the Environment offered to consult with the governments of the provinces and the members of the National Advisory Committee who are representatives of Aboriginal governments;

Therefore, Her Excellency the Governor General in Council, on the recommendation of the Minister of the Environment, makes the annexed Clean Fuel Regulations under sections 140 Footnote c and 326 and subsection 330(2) of the Canadian Environmental Protection Act, 1999 Footnote b and subsection 5(1) of the Environmental Violations Administrative Monetary Penalties Act Footnote d.

Interpretation

Marginal note:Definitions

  •  (1) The following definitions apply in these Regulations.

    account holder

    account holder, with respect to any account opened under section 28, means the primary supplier or registered creator for whom the Minister opened the account. (titulaire)

    Act

    Act means the Canadian Environmental Protection Act, 1999. (Loi)

    authorized agent

    authorized agent means, 

    • (a) in respect of a corporation, any officer of the corporation who is authorized to act on its behalf;

    • (b) in respect of an individual, that individual or any person authorized to act on behalf of that individual; and

    • (c) in respect of any other entity, any person authorized to act on behalf of that entity. (agent autorisé)

    baseline carbon intensity

    baseline carbon intensity means the weighted average carbon intensity of the gasoline or diesel used in Canada for the year 2016, as set out in subsection 5(3). (intensité en carbone de base)

    biogas

    biogas means a gaseous mixture that is recovered from the anaerobic decomposition of biomass and that consists primarily of methane and carbon dioxide and contains other constituents that prevent it from meeting the standard for injection into the nearest natural gas pipeline. (biogaz)

    biomass

    biomass means the biodegradable fraction of products, waste and residues of a biological origin — including plant and animal substances — originating from agriculture, forestry and other industries, such as fishing and aquaculture, as well as the fraction of waste, including industrial and municipal waste, of a biological origin. (biomasse)

    carbon intensity

    carbon intensity, in relation to a fuel, energy source, or material input that is renewable natural gas, biogas, renewable propane or hydrogen, means the quantity in grams of CO2e per megajoule of energy contained in that fuel, energy source or material input that is released over the life cycle of that fuel, energy source or material input, including during the activities carried out during the stages of the life cycle, such as

    • (a) the extraction or production of the feedstock used to produce the fuel, energy source or material input;

    • (b) the processing, refining or upgrading of the feedstock to produce the fuel, energy source or material input;

    • (c) the transportation or distribution of the feedstock, of intermediary products or of the fuel, energy source or material input; and

    • (d) the combustion of the fuel. (intensité en carbone)

    carbon-intensity contributor

    carbon-intensity contributor means a person who applies for the approval of a carbon intensity under subsection 80(1) for a set of activities carried out over the life cycle of a fuel in the liquid class or a low-carbon-intensity fuel with the intention to transfer the approved carbon intensity to a registered creator or foreign supplier or to another carbon-intensity contributor. (contributeur à l’intensité en carbone)

    charging-network operator

    charging-network operator means a person who operates a communication platform that collects data on the electricity supplied by a charging station and who is the owner of that data. (exploitant d’un réseau de recharge)

    charging-site host

    charging-site host means a person who owns or leases a charging station and who has the legal right to have the charging station installed.  (hôte d’une station de recharge) 

    charging station

    charging station means a device that is used in Canada to charge the battery on board an electric vehicle by supplying electricity to the electric vehicle and that is capable of communicating with a server, whether through the Internet or using a cellular signal or connected vehicle communications, to report the quantity of electricity supplied and the time at which it is supplied. (borne de recharge)

    CO2e

    CO2e means the quantity of carbon dioxide, expressed in grams or tonnes, that would be required to produce a warming effect equivalent to another greenhouse gas over a particular period of time, as set out in the Fuel LCA Model. (CO2e)

    compliance-credit transfer system

    compliance-credit transfer system means the system administered by the Minister for the transfer of credits in accordance with sections 105 to 112.  (mécanisme de cession des unités de conformité)

    compliance period

    compliance period means

    • (a) the period that begins on the day on which these Regulations are registered and ends on December 31, 2022;

    • (b) the period that begins on January 1, 2023 and ends on June 30, 2023;

    • (c) the period that begins on July 1, 2023 and ends on December 31, 2023; or

    • (d) after December 31, 2023, each calendar year. (période de conformité)

    co-processed low-carbon-intensity fuel

    co-processed low-carbon-intensity fuel means the portion of a fuel that is produced from a mixture of a petroleum feedstock and a non-petroleum feedstock that are used simultaneously in the same processing unit of a petroleum refinery or upgrader facility and that is a low-carbon-intensity fuel derived from a non-petroleum feedstock.  (combustible cotraité à faible intensité en carbone)

    co-processed low-carbon-intensity propane

    co-processed low-carbon-intensity propane means a co-processed low-carbon-intensity fuel that is a mixture that is gaseous at standard conditions and consists primarily of propane. (propane cotraité à faible intensité en carbone)

    crop

    crop includes a woody biomass crop with a rotational period that is not more than 25 years. (culture)

    deferred portion of the reduction requirements

    deferred portion of the reduction requirements, with respect to a compliance period, means the portion of the sum of the reduction requirements in respect of gasoline and diesel for that compliance period that has been deferred by a primary supplier in accordance with section 16, as increased in accordance with section 17 and as reduced in accordance with section 18. (partie reportée des exigences de réduction)

    diesel

    diesel means liquid petroleum fuel that

    • (a) is sold or represented as diesel or as a fuel suitable for use in a diesel engine; or

    • (b) evaporates at atmospheric pressure, has a boiling point between 130°C and 400°C and is suitable for use in a diesel engine. (diesel)

    diesel replacement

    diesel replacement means a liquid low-carbon-intensity fuel that is suitable for use in a diesel engine, furnace or open flame burner or that is used in aviation. (substitut du diesel)

    electric vehicle

    electric vehicle means a vehicle that is propelled by an electric motor whose source of electricity is a rechargeable battery that is charged from a source of electricity that is not on board the vehicle. It includes a plug-in hybrid electric vehicle. (véhicule électrique)

    eligible feedstock

    eligible feedstock means a feedstock that is eligible under section 46 and meets the requirements set out in sections 48 to 52, except if it is exempted under any of sections 53 to 55, as well as the requirements set out in section 57.  (charge d’alimentation admissible)

    EPA

    EPA means the United States Environmental Protection Agency.  (EPA)

    foreign supplier

    foreign supplier means the owner of a facility outside Canada at which a low-carbon-intensity fuel is produced or the person who leases, operates, controls or manages such a facility. (fournisseur étranger)

    Fuel LCA Model

    Fuel LCA Model means the fuel life-cycle assessment model that is developed by the Minister in accordance with ISO Standard 14040 and that consists of the procedures that must be followed to determine the carbon intensity of a fuel, energy source or material input using life-cycle inventories for various pathways. (modèle ACV des combustibles)

    fuelling station

    fuelling station means a facility in Canada at which vehicles are supplied with fuel or with hydrogen used as an energy source and includes a mobile facility. (station de ravitaillement)

    gaseous class

    gaseous class means a class of fuel consisting of propane and natural gas. (catégorie des combustibles gazeux)

    gasoline

    gasoline means liquid petroleum fuel that

    • (a) is sold or represented as gasoline, as a fuel suitable for use in a spark-ignition engine or as a fuel requiring only the addition of a low-carbon-intensity fuel or an oxygenate to make it suitable for use in a spark-ignition engine; or

    • (b) is suitable for use in a spark-ignition engine and has, as determined by the applicable test method listed in National Standard of Canada CAN/CGSB-3.5-2021, entitled Automotive Gasoline, the following characteristics:

      • (i) a vapour pressure of no less than 38 kPa,

      • (ii) an anti-knock index of no less than 80,

      • (iii) a distillation temperature at which 10% of the fuel has evaporated of no less than 35°C and no more than 70°C, and

      • (iv) a distillation temperature at which 50% of the fuel has evaporated of no less than 65°C and no more than 120°C. (essence)

    gasoline replacement

    gasoline replacement means a liquid low-carbon-intensity fuel that is suitable for use in a spark-ignition engine.  (substitut de l’essence)

    GPS

    GPS means global positioning system. (GPS)

    hydrogen fuel cell vehicle

    hydrogen fuel cell vehicle means a vehicle propelled solely by an electric motor that uses electricity produced by an electrochemical cell from hydrogen. (véhicule à pile à hydrogène)

    ISO/IEC Standard 17011

    ISO/IEC Standard 17011 means International Standard ISO/IEC 17011, entitled Conformity assessment — Requirements for accreditation bodies accrediting conformity assessment bodies, published by the International Organization for Standardization. (norme ISO/IEC 17011)

    ISO/IEC Standard 17021-1

    ISO/IEC Standard 17021-1 means the International Standard ISO/IEC 17021-1, entitled Conformity assessment — Requirements for bodies providing audit and certification of management systems — Part 1: Requirements, published by the International Organization for Standardization (norme ISO/IEC 17021-1)

    ISO/IEC Standard 17065

    ISO/IEC Standard 17065 means the International Standard ISO/IEC 17065, entitled Conformity assessment — Requirements for bodies certifying products, processes and services, published by the International Organization for Standardization. (norme ISO/IEC 17065)

    ISO Standard 14040

    ISO Standard 14040 means the International Standard ISO 14040, entitled Environmental management — Life cycle assessment — Principles and framework, published by the International Organization for Standardization. (norme ISO 14040)

    ISO Standard 14044

    ISO Standard 14044 means the International Standard ISO 14044, entitled Environmental management — Life cycle assessment — Requirements and guidelines, published by the International Organization for Standardization. (norme ISO 14044)

    ISO Standard 14064-2

    ISO Standard 14064-2 means the International Standard ISO 14064-2, entitled Greenhouse gases — Part 2: Specification with guidance at the project level for quantification, monitoring and reporting of greenhouse gas emission reductions or removal enhancements, published by the International Organization for Standardization. (norme ISO 14064-2)

    ISO Standard 14064-3:2019

    ISO Standard 14064-3:2019 means the International Standard ISO 14064-3:2019, entitled Greenhouse gases — Part 3: Specification with guidance for the verification and validation of greenhouse gas statements, published by the International Organization for Standardization, as it read on May 1, 2019. (norme ISO 14064-3:2019)

    ISO Standard 19011

    ISO Standard 19011 means the International Standard ISO 19011, entitled Guidelines for auditing management systems, published by the International Organization for Standardization. (norme ISO 19011)

    liquid class

    liquid class means a class of fuel consisting of the fossil fuels that are liquid at standard conditions.  (catégorie des combustibles liquides)

    low-carbon-intensity fuel

    low-carbon-intensity fuel means a liquid or gaseous fuel that is not a fuel in the liquid class or gaseous class and that has a carbon intensity, for the compliance period during which the fuel was produced or imported, that does not exceed

    • (a) 90% of the reference carbon intensity set out for that compliance period in item 1, column 2, of Schedule 1, in the case of a fuel that is in the liquid state at standard conditions;

    • (b) the reference carbon intensity set out for that compliance period in item 2, column 2, of Schedule 1, in the case of compressed renewable natural gas and liquefied renewable natural gas referred to in subsection 99(1), renewable natural gas referred to in subsection 100(1) or hydrogen referred to in paragraph 104(1)(b);

    • (c) the reference carbon intensity set out for that compliance period in item 3, column 2, of Schedule 1, in the case of renewable propane referred to in subsection 99(1) or 100(1) and co-processed low-carbon-intensity propane referred to in subsection 99(1);

    • (d) 90% of the reference carbon intensity set out for that compliance period in item 2, column 2, of Schedule 1, in the case of biogas or in the case of renewable natural gas and hydrogen that is not referred to in paragraph (b); or

    • (e) 90% of the reference carbon intensity set out for that compliance period in item 3, column 2, of Schedule 1, in the case of renewable propane and co-processed low-carbon-intensity propane that is not referred to in paragraph (c). (combustible à faible intensité en carbone)

    marine vessel

    marine vessel means any boat, ship or other vessel that is designed, used or capable of being used for navigation in, on or through water but is not designed for self-propulsion out of water. (navire)

    Methods for Verification and Certification

    Methods for Verification and Certification means the document entitled Methods for Verification and Certification — Clean Fuel Regulations that is developed and published by the Minister. (Méthodes de vérification et de certification)

    misstatement

    misstatement means an error, ommission or misreporting, as defined in Methods for Verification and Certification, in an application or report referred to in these Regulations.  (déclaration erronée)

    participant

    participant means a primary supplier who is registered with the Minister in accordance with subsection 10(1) or a registered creator who participates in the compliance-credit transfer system. (participant)

    petroleum feedstock

    petroleum feedstock means crude oil or a substance derived from crude oil or natural gas, if it is primarily used as a feedstock to produce a fossil fuel in a petroleum refinery or upgrader facility, but it does not include any feedstock that is derived from petrochemicals or other hydrocarbon streams that have undergone additional processing, such as gas-to-liquid processing. (charge d’alimentation à base de pétrole)

    primary supplier

    primary supplier means a person who

    • (a) owns, leases, operates, controls or manages a fuel production facility in Canada at which gasoline or diesel is produced; or

    • (b) imports gasoline or diesel into Canada. (fournisseur principal)

    provisional compliance credit

    provisional compliance credit means a compliance credit referred to in subsection 23(1). (unité de conformité provisoire)

    reduction requirement

    reduction requirement means the reduction requirement determined in accordance with section 9. (exigence de réduction)

    registered creator

    registered creator means a person registered with the Minister in accordance with subsection 25(1). (créateur enregistré)

    renewable natural gas

    renewable natural gas means gas that meets the standard for injection into the closest natural gas pipeline and that is either synthetic natural gas derived from biomass or gas derived from the processing of biogas. (gaz naturel renouvelable)

    renewable propane

    renewable propane means a mixture that is gaseous at standard conditions, is recovered from the processing of biomass and consists primarily of propane, but it does not include co-processed low-carbon-intensity propane. (propane renouvelable)

    residue

    residue means a substance that is produced in a production process but whose production is not a primary aim of the process. It does not include any substance that the process has been deliberately modified to produce. (résidu)

    scheme owner

    scheme owner has the same meaning as in subclause 3.11 of ISO/IEC Standard 17065. (propriétaire du régime)

    Specifications for Fuel LCA Model CI Calculations

    Specifications for Fuel LCA Model CI Calculations means the specifications that are developed and published by the Minister in respect of the calculation of the carbon intensity of a fuel, energy source or material input using the Fuel LCA Model. (spécifications pour le calcul de l’IC au moyen du modèle ACV des combustibles)

    standard conditions

    standard conditions means a temperature of 15°C (59°F) and a pressure of 101.325 kPa (14.696 psia). (conditions normales)

    total reduction requirement

    total reduction requirement means the sum of the reduction requirements in respect of gasoline and diesel for the compliance period that ended most recently, and the deferred portion of the reduction requirements for each preceding compliance period. (exigence de réduction totale)

    verification body

    verification body means a verification body referred to in section 137.  (organisme de vérification)

  • Marginal note:Hydrogen used as energy source

    (2) For the purposes of these Regulations, hydrogen referred to in paragraph 104(1)(a) is deemed to be a low-carbon-intensity fuel if the carbon intensity of the hydrogen, for the compliance period during which the hydrogen is used, does not exceed the reference carbon intensity set out for that compliance period in item 2, column 2, of Schedule 1.

  • Marginal note:Compressed gas and liquefied gas

    (3) In these Regulations,

    • (a) a reference to hydrogen includes compressed hydrogen and liquefied hydrogen;

    • (b) a reference to natural gas includes compressed natural gas and liquefied natural gas; and

    • (c) a reference to renewable natural gas includes compressed renewable natural gas and liquefied renewable natural gas.

  • Marginal note:Co-processed low-carbon-intensity fuel

    (4) The following provisions do not apply in respect of a co-processed low-carbon-intensity fuel:

Marginal note:Incorporation by reference

  •  (1) A standard or method that is incorporated by reference in these Regulations, other than ISO Standard 14064-3:2019, is incorporated as amended from time to time.

  • Marginal note:Interpretation of documents incorporated by reference

    (2) For the purpose of interpreting any document that is incorporated by reference in these Regulations, a reference to “should” in the English version of the document is to be read as “must” and any recommendation or suggestion is to be read as an obligation unless the context requires otherwise. For greater certainty, in the case of the accuracy or precision of a measurement, the context never requires otherwise.

  • Marginal note:Inconsistencies with these Regulations

    (3) In the event of an inconsistency between a provision in a document incorporated by reference into these Regulations and any provision of these Regulations, the provision of these Regulations prevails to the extent of the inconsistency.

Marginal note:Standard conditions

 Unless otherwise specified, a reference in these Regulations to a volume or quantity of gas or liquid that is expressed in cubic metres is a reference to the volume or quantity of that gas or liquid at standard conditions.

Application

Marginal note:Exemption — primary suppliers

  •  (1) A primary supplier who produces in Canada or imports into Canada a volume of less than 400 m3 of gasoline or a volume of less than 400 m3 of diesel during a compliance period is exempt from the application of these Regulations with respect to that fuel for that compliance period.

  • Marginal note:Non-application — certain fuels

    (2) These Regulations do not apply in respect of gasoline or diesel that is

    • (a) aviation gasoline;

    • (b) exported from Canada;

    • (c) used for scientific research, other than research on consumer preferences in respect of various properties of fuels or market research; or

    • (d) sold or delivered for the purpose of supplying the engine of a vehicle, including a marine vessel, that is used exclusively for competition.

  • Marginal note:Exception

    (3) However, a primary supplier who, during a compliance period, produces in Canada or imports into Canada a volume of 400 m3 or more of gasoline or diesel must record the volume of every fuel referred to in paragraphs (2)(a) to (d) that is produced or imported during that compliance period and must include that information in the compliance report submitted to the Minister under section 127.

  • Marginal note:Clarification

    (4) For greater certainty, the fuels referred to in paragraphs (2)(a) to (d) are not included when determining, for the purposes of subsection (1), the volume of fuel that is produced in Canada or imported into Canada by a primary supplier.

Requirements for Liquid Fuels

Carbon-Intensity Limits

Marginal note:Requirement — carbon intensity

  •  (1) For the purposes of section 139 of the Act, a primary supplier’s pool — as determined in accordance with section 8 — of a liquid fossil fuel that is set out in column 1 of the table to this subsection must not have a carbon intensity that is greater than the corresponding limit set out in column 2 for the corresponding compliance period.

    TABLE

    Fuel Carbon-Intensity Limits

    Column 1Column 2
    Limit for Each Compliance Period (gCO2e/MJ)
    ItemLiquid Fossil Fuel20232024202520262027202820292030 and after
    1Gasoline91.590.088.587.085.584.082.581.0
    2Diesel89.588.086.585.083.582.080.579.0
  • Marginal note:Lowering of carbon intensity

    (2) A primary supplier must comply with subsection (1) with respect to a fuel for a compliance period by lowering the carbon intensity of their pool of that fuel for that compliance period by an amount that is equal to the difference between the baseline carbon intensity for that fuel and the limit set out in the table to subsection (1) for that fuel and that compliance period. The carbon intensity must be lowered by using compliance credits in accordance with section 11 to satisfy the reduction requirement for that compliance period.

  • Marginal note:Baseline carbon intensity

    (3) For the purposes of subsection (2), the baseline carbon intensity of gasoline is 95 gCO2e/MJ and the baseline carbon intensity of diesel is 93 gCO2e/MJ.

  • Marginal note:Non-application

    (4) Subsection (1) does not apply in respect of a fuel that is produced in Canada or imported into Canada before July 1, 2023.

Marginal note:Volumetric requirement — gasoline

  •  (1) For the purposes of section 139 of the Act, at least 5% of the volume of a primary supplier’s pool of gasoline — as determined in accordance with section 8 — must, for each compliance period, be displaced by an equivalent volume of a gasoline replacement.

  • Marginal note:Exception — Newfoundland and Labrador

    (2) For the purposes of subsection (1), the primary supplier may, for a compliance period, subtract from their pool of gasoline determined in accordance with section 8 any volume of gasoline that, during the compliance period, the primary supplier produced in or imported into Newfoundland and Labrador and sold or delivered for use in that province, if the primary supplier records information that establishes that the volume of gasoline met those conditions.

  • Marginal note:Non-application

    (3) Subsection (1) does not apply in respect of gasoline that is produced in Canada or imported into Canada before July 1, 2023.

Marginal note:Volumetric requirement — diesel

  •  (1) For the purposes of section 139 of the Act, at least 2% of the volume of a primary supplier’s pool of diesel — as determined in accordance with section 8 — must, for each compliance period, be displaced by an equivalent volume of a diesel replacement.

  • Marginal note:Exception — Newfoundland and Labrador

    (2) For the purposes of subsection (1), the primary supplier may, for a compliance period, subtract from their pool of diesel determined in accordance with section 8 any volume of diesel that, during the compliance period, the primary supplier produced in or imported into Newfoundland and Labrador and sold or delivered for use in that province, if the primary supplier records information that establishes that the volume of diesel met those conditions.

  • Marginal note:Non-application

    (3) Subsection (1) does not apply in respect of diesel that is produced in Canada or imported into Canada before July 1, 2023.

Marginal note:Pool of liquid fuel — volume

  •  (1) A primary supplier must, for each compliance period, determine the total volume, expressed in cubic metres, of their pool of gasoline or diesel, as the case may be, that was

    • (a) produced by the primary supplier at a fuel production facility in Canada and, during the compliance period, either

      • (i) dispatched from the fuel production facility, or

      • (ii) used to fuel a vehicle or other mobile equipment at the fuel production facility; or

    • (b) imported by the primary supplier into Canada during the compliance period.

  • Marginal note:Subtraction from pool

    (2) However, a primary supplier may, for each compliance period, subtract from their pool of gasoline or diesel, as the case may be, any volume of that fuel, if the primary supplier, before the August 1 of the calendar year that follows the end of the compliance period, records information that establishes that the volume of fuel met any of the following conditions during the compliance period:

    • (a) it was sold or delivered for a use other than combustion;

    • (b) it was sold or delivered for use in a marine vessel that had a non-Canadian port as its destination;

    • (c) it was sold or delivered for use for non-industrial purposes in a geographic area that is served by neither an electrical distribution network that is subject to the standards of the North American Electric Reliability Corporation nor a natural gas distribution system;

    • (d) it was sold or delivered for the purpose of space heating;

    • (e) it was sold or delivered for use in the generation of electricity in a geographic area that is served by neither an electrical distribution network that is subject to the standards of the North American Electric Reliability Corporation nor a natural gas distribution system.

Reduction Requirement

Marginal note:Reduction in tonnes

 The carbon intensity of a pool of gasoline or diesel for a compliance period is considered to be lowered for the purposes of subsection 5(2) if the number of tonnes of CO2e released over the life cycle of that fuel is reduced by the value of the reduction requirement for that compliance period, as determined by the formula

CIdiff × (Q × D) × 10-6

where

CIdiff
is the difference, expressed in gCO2e/MJ, between the baseline carbon intensity of that fuel, as set out in subsection 5(3), and the limit for that fuel for that compliance period, as set out in column 2 of the table to subsection 5(1);
Q
is the volume of that pool for the compliance period, as determined in accordance with section 8 and expressed in cubic metres; and
D
is, at the election of the primary supplier, the energy density of the fuel as set out in column 2 of Schedule 2 or as set out in the Specifications for Fuel LCA Model CI Calculations.

Registration as Primary Supplier

Marginal note:Registration report

  •  (1) A primary supplier must register with the Minister by submitting a registration report to the Minister that contains the information referred to in sections 1 to 3 of Schedule 3 no later than 45 days after the day on which they have produced in Canada or imported into Canada, during a compliance period, a total volume of 400 m3 or more of gasoline or a total volume of 400 m3 or more of diesel.

  • Marginal note:Exception — registration within 90 days

    (2) However, the registration report may be submitted at any time during the period that begins on the day on which these Regulations are registered and ends 90 days after that day.

  • Marginal note:Change of information

    (3) If there are any changes in the information referred to in section 1 of Schedule 3 that is provided in the registration report, the primary supplier must send a notice to the Minister that provides the updated information within 30 days after the day on which the change occurs.

  • Marginal note:Notice of cancellation

    (4) A primary supplier who is not required by subsection (1) to be registered for a given compliance period and who has complied with the requirements set out in these Regulations for all of the previous compliance periods, including the volumetric requirements set out in subsections 6(1) and 7(1) and the reduction requirement, may cancel their registration as a primary supplier by sending a notice to that effect to the Minister.

  • Marginal note:Cancellation by Minister

    (5) If, after receiving the notice referred to in subsection (4), the Minister is satisfied that the primary supplier has complied with these Regulations for all previous compliance periods, the Minister must

    • (a) if the primary supplier is not a registered creator, cancel any compliance credits in their accounts opened under section 28;

    • (b) cancel their registration as a primary supplier; and

    • (c) send a notice to the primary supplier informing them that their registration has been cancelled.

  • Marginal note:Clarification

    (6) For greater certainty, subsection (1) applies to a primary supplier whose registration was cancelled by the Minister under subsection (5).

Compliance Credits

Use

Marginal note:Satisfaction of reduction requirement

  •  (1) A primary supplier must use the compliance credits that they create under sections 19 and 20, or that are transferred to them under the compliance-credit transfer system, to satisfy the total reduction requirement.

  • Marginal note:Deemed reduction

    (2) The use of one compliance credit by a primary supplier for gasoline or diesel that is produced in Canada or imported into Canada during a compliance period is deemed to reduce by one tonne the quantity of CO2e released over the life cycle of that fuel during that compliance period.

  • Marginal note:Prior creation of provisional credit

    (3) The primary supplier must use only the compliance credits that are created as provisional compliance credits before the end of a compliance period or the compliance credits that they create under subsection 19(2) to satisfy the reduction requirement for that compliance period.

  • Marginal note:Cancellation after use

    (4) The Minister must cancel a compliance credit immediately after it is used.

Marginal note:Deemed compliance — gasoline

  •  (1) For the purposes of subsection 6(1), a compliance credit that was created under paragraph 19(1)(a), (b) or (c) by producing in Canada or importing into Canada a volume of a gasoline replacement, and that is used by a primary supplier in accordance with section 11 for a compliance period, is deemed to displace, for that compliance period, the use of an equivalent volume of the primary supplier’s pool of gasoline.

  • Marginal note:Deemed compliance — diesel

    (2) For the purposes of subsection 7(1), a compliance credit that was created under paragraph 19(1)(a), (b) or (c) by producing in Canada or importing into Canada a volume of a diesel replacement, and that was used by a primary supplier in accordance with section 11 for a compliance period, is deemed to displace, for that compliance period, the use of an equivalent volume of the primary supplier’s pool of diesel.

  • Marginal note:Prior creation of provisional credit

    (3) The primary supplier must use only the compliance credits that are created as provisional compliance credits before the end of a compliance period to comply with the volumetric requirements set out in subsections 6(1) and 7(1) for that compliance period.

Marginal note:July 31 — gasoline

  •  (1) For the purposes of subsection 12(1), a primary supplier must, no later than the July 31 that follows the end of a compliance period, use — in accordance with subsection 12(3) — the compliance credits that are in their account opened under paragraph 28(a), until

    • (a) the volumetric requirement set out in subsection 6(1) is met for that compliance period; or

    • (b) no such compliance credits remain in that account.

  • Marginal note:July 31 — diesel

    (2) For the purposes of subsection 12(2), a primary supplier must, no later than the July 31 that follows the end of a compliance period, use — in accordance with subsection 12(3) — the compliance credits that are in their account opened under paragraph 28(a), until

    • (a) the volumetric requirement set out in subsection 7(1) is met for that compliance period; or

    • (b) no such compliance credits remain in that account.

  • Marginal note:July 31 — contribution to funding program

    (3) For the purposes of section 11 and subject to subsection 15(1), a primary supplier must, no later than the July 31 that follows the end of a compliance period, use all of the compliance credits that they created by contributing to a registered emission-reduction funding program in accordance with paragraph 118(1)(a) to satisfy the reduction requirement for that compliance period.

  • Marginal note:July 31 — reduction requirement

    (4) For the purposes of section 11 and subject to subsections 15(2) and (3), a primary supplier must, no later than the July 31 that follows the end of a compliance period, use the compliance credits that are in their accounts opened under section 28, until

    • (a) the reduction requirement is satisfied for that compliance period; or

    • (b) no such compliance credits remain in those accounts.

  • Marginal note:Choice of compliance credits

    (5) Subject to subsections (1) and (2), if the circumstances described in paragraph (4)(a) occur before the circumstances described in paragraph (4)(b), the primary supplier must satisfy the reduction requirement by using compliance credits that are chosen by them and indicated in the report submitted under subsection 127(1).

  • Marginal note:August 1 — cancellation of credits

    (6) On the August 1 that follows the end of a compliance period, if any of the compliance credits referred to in subsection (3) have not been used by the primary supplier, the Minister must cancel those credits.

  • Marginal note:Non-application — subsections (1) to (4)

    (7) Subsections (1) to (4) do not apply in respect of any compliance period that ends before July 1, 2023.

Marginal note:December 15 — gasoline

  •  (1) For the purposes of subsection 12(1), if a primary supplier, on the August 1 that follows the end of a compliance period, has not complied with the volumetric requirement set out in subsection 6(1) for that compliance period, the primary supplier must, no later than the following December 15, comply with that requirement by using the compliance credits transferred to them under section 112.

  • Marginal note:December 15 — diesel

    (2) For the purposes of subsection 12(2), if a primary supplier, on the August 1 that follows the end of a compliance period, has not complied with the volumetric requirement set out in subsection 7(1) for that compliance period, the primary supplier must, no later than the following December 15, comply with that requirement by using the compliance credits transferred to them under section 112.

  • Marginal note:Other credits

    (3) For the purposes of section 11 and subject to subsection 15(1), if a primary supplier, on the August 1 that follows the end of a compliance period, has not satisfied the reduction requirement for that compliance period, the primary supplier must, no later than the December 15 that follows the end of that compliance period, use the compliance credits that were transferred to them under section 112, or that they created by contributing to a registered emission-reduction funding program in accordance with paragraph 118(1)(b), to satisfy that reduction requirement.

  • Marginal note:Compliance — December 15

    (4) Subject to sections 16 to 18, a primary supplier must, no later than the December 15 that follows the end of a compliance period, use the compliance credits in their accounts opened under section 28 to satisfy the total reduction requirement and comply with the volumetric requirements set out in subsections 6(1) and 7(1) for that compliance period.

  • Marginal note:December 16 — cancellation

    (5) On the December 16 that follows the expiry of a compliance period, if any of the compliance credits that are referred to in subsection (3) have not been used by the primary supplier, the Minister must cancel those credits.

  • Marginal note:Non-application — subsections (1) to (4)

    (6) Subsections (1) to (4) do not apply in respect of any compliance period that ends before July 1, 2023.

Marginal note:Limits on credit use — funding program

  •  (1) The primary supplier must ensure that the total number of compliance credits created under subsection 19(2) — that are used in accordance with subsections 13(3) and 14(3), paragraph 18(1)(a) and subsection 18(3) during the calendar year that follows the end of a compliance period — does not exceed 10% of the primary supplier’s total reduction requirement.

  • Marginal note:Limit — paragraph 28(b)

    (2) The primary supplier must ensure that the total number of compliance credits in their account opened under paragraph 28(b) — that are used in accordance with subsection 13(4) and paragraph 18(1)(b) during the calendar year that follows the end of a compliance period — does not exceed 10% of the primary supplier’s total reduction requirement.

  • Marginal note:Limit — generic quantification method

    (3) The primary supplier must ensure that the total number of compliance credits created under paragraph 19(1)(a) in respect of a project for which a generic emission-reduction quantification method is applicable — that are used in accordance with subsection 13(4) and paragraphs 18(1)(b) and (c) during the calendar year that follows the end of a compliance period — does not exceed 10% of the primary supplier’s total reduction requirement.

Marginal note:Deferral of reduction requirements

  •  (1) A primary supplier may, no later than the December 15 that follows the end of a compliance period, defer satisfaction of their reduction requirements for that compliance period by any number of compliance credits that does not exceed the greater of zero and the result of the formula

    10% x Rcurrent − Rdeferred

    where

    Rcurrent
    is the sum of their reduction requirements in respect of gasoline and diesel for that compliance period; and
    Rdeferred
    is the sum of all deferred portions of the reduction requirements in respect of gasoline and diesel for previous compliance periods.
  • Marginal note:Conditions for deferral

    (2) The primary supplier may defer a portion of their reduction requirements for a compliance period under subsection (1) only if

    • (a) the Minister has sent a notice in accordance with subsection 111(2) for that compliance period or the primary supplier has acquired by transfer through the compliance-credit clearance mechanism the number of compliance credits determined in accordance with paragraph 112(5)(b) for that compliance period; and

    • (b) the primary supplier has created enough compliance credits by contributing to a registered emission-reduction funding program to satisfy 10% of the total reduction requirement for that compliance period in respect of all types of fuels.

  • Marginal note:Compliance required after five years

    (3) A primary supplier who defers under subsection (1) a portion of their reduction requirements for a compliance period must satisfy the deferred portion no later than the December 15 that follows the fifth anniversary of the end of that compliance period.

Marginal note:Increase to deferred portion

 On each December 16 that follows the end of a compliance period for which a portion of the reduction requirements is deferred under subsection 16(1) and that precedes the fifth anniversary of the end of that compliance period, the deferred portion of the reduction requirements is to be multiplied by 1.05.

Marginal note:Reduction — July 31

  •  (1) In order to reduce a deferred portion of the reduction requirements in accordance with section 11, the primary supplier must, during the period that begins on the day after a compliance period expires and ends on the July 31 that follows that day, use the following compliance credits that are in their accounts opened under section 28 and that exceed the number required to satisfy the reduction requirements for the compliance period that ended most recently:

    • (a) subject to subsection 15(1), all of the compliance credits that they created by contributing to a registered emission-reduction funding program in accordance with paragraph 118(1)(a);

    • (b) subject to subsections 15(2) and (3), any compliance credits in their account opened under paragraph 28(b); and

    • (c) subject to subsection 15(3), any compliance credits in their account opened under paragraph 28(a).

  • Marginal note:Election

    (2) If the primary supplier has more credits than the number required to satisfy the deferred portion of the reduction requirements in accordance with subsection (1), they may elect to use any number of compliance credits referred to in paragraphs (1)(b) and (c) to satisfy the deferred portion of the reduction requirements.

  • Marginal note:Reduction — December 15

    (3) Subject to subsection 15(1), if a primary supplier, on the August 1 that follows the end of a compliance period, has not satisfied the deferred portion of the reduction requirements for a previous compliance period in accordance with subsection (2), the primary supplier must, no later than the following December 15, reduce the deferred portion of the reduction requirements by using all of the compliance credits in their account opened under paragraph 28(a) — that were transferred to them through the compliance-credit clearance mechanism under section 112 or that they created by contributing to a registered emission-reduction funding program in accordance with paragraph 118(1)(b) — that exceed the number of compliance credits required to satisfy their reduction requirements for the compliance period that ended most recently.

  • Marginal note:Multiple compliance periods

    (4) If a primary supplier has not satisfied the deferred portion of the reduction requirements for more than one previous compliance period, they must not use any compliance credits to reduce the deferred portion of the reduction requirements in accordance with subsection (1) or (3) for a particular compliance period unless they have satisfied the deferred portion of the reduction requirements for every compliance period that precedes that particular compliance period.

  • Marginal note:Non-application

    (5) Subsections (1) to (4) do not apply before January 1, 2025.

Creation

Reduction of CO2e Emissions

Marginal note:Liquid class

  •  (1) A registered creator may create a compliance credit in respect of the liquid class in the following cases:

    • (a) the registered creator, or a person with whom they have entered into an agreement under section 21, lowers the carbon intensity of a fuel in the liquid class by carrying out, in respect of that fuel, a CO2e-emission-reduction project that is described in section 30 and that is recognized under subsection 35(1), 36(1), 37(3), 39(1) or 40(3), as the case may be;

    • (b) the registered creator imports into Canada a quantity of low-carbon-intensity fuel to which may be attributed a reduction in the number of tonnes of CO2e that would otherwise have been emitted by the use of a fuel in the liquid class, if the low-carbon-intensity fuel

      • (i) is in the liquid state at standard conditions,

      • (ii) is one referred to in section 94,

      • (iii) is used or sold for use as a fuel in Canada whether as neat fuel or as part of a blend, and

      • (iv) meets the requirements set out in section 56;

    • (c) the registered creator, or a person with whom they have entered into an agreement under section 21, produces in Canada a quantity of low-carbon-intensity fuel to which may be attributed a reduction in the number of tonnes of CO2e that would otherwise have been emitted by the use of a fuel in the liquid class, if the low-carbon-intensity fuel

      • (i) is in the liquid state at standard conditions,

      • (ii) is one referred to in section 94,

      • (iii) is used or sold for use as a fuel in Canada whether as neat fuel or as part of a blend, and

      • (iv) meets the requirements set out in section 56; or

    • (d) the registered creator, or a person with whom they have entered into an agreement under section 21, reduces the number of tonnes of CO2e emissions by displacing the use in Canada of a quantity of fuel in the liquid class as a fuel for a vehicle with the use in Canada of

      • (i) a quantity of propane, compressed natural gas or liquefied natural gas as a fuel for a vehicle, in accordance with section 98,

      • (ii) a quantity of renewable propane, co-processed low-carbon-intensity propane, compressed renewable natural gas or liquefied renewable natural gas that meets the requirements set out in section 56 as a fuel for a vehicle, in accordance with section 99,

      • (iii) a quantity of renewable propane or renewable natural gas that meets the requirements set out in section 56 as a fuel for a vehicle, in accordance with section 100,

      • (iv) a quantity of electricity as an energy source for an electric vehicle, in accordance with sections 101 and 102, or

      • (v) a quantity of hydrogen that meets the requirements set out in section 56, in accordance with section 104,

        • (A) as an energy source for a hydrogen fuel cell vehicle, or

        • (B) as a fuel for a vehicle other than a hydrogen fuel cell vehicle.

  • Marginal note:Contribution to funding program

    (2) A primary supplier may create a compliance credit in respect of the liquid class if they make a contribution to a registered emission-reduction funding program in accordance with section 118.

Marginal note:Gaseous class

 A registered creator may create a compliance credit in respect of the gaseous class in the following cases:

  • (a) the registered creator, or a person with whom they have entered into an agreement under section 21, lowers the carbon intensity of a fuel in the gaseous class by carrying out, in respect of that fuel, a CO2e-emission-reduction project described in paragraph 30(d) that reduces the carbon intensity of a fuel in the liquid class and is recognized under subsection 36(1), 37(3), 39(1) or 40(3), as the case may be;

  • (b) the registered creator imports into Canada a quantity of low-carbon-intensity fuel to which may be attributed a reduction in the number of tonnes of CO2e that would otherwise have been emitted by the use of a fuel in the gaseous class, if the low-carbon-intensity fuel

    • (i) is biogas, renewable natural gas, renewable propane or hydrogen,

    • (ii) is one referred to in section 95,

    • (iii) is used or sold for use as a fuel in Canada whether as neat fuel or as part of a blend, and

    • (iv) meets the requirements set out in section 56; or

  • (c) the registered creator, or a person with whom they have entered into an agreement under section 21, produces in Canada a quantity of low-carbon-intensity fuel to which may be attributed a reduction in the number of tonnes of CO2e that would otherwise have been emitted by the use of a fuel in the gaseous class, if the low-carbon-intensity fuel

    • (i) is biogas, renewable natural gas, renewable propane or hydrogen,

    • (ii) is one referred to in section 95 or 96, as the case may be,

    • (iii) is used or sold for use as a fuel in Canada whether as neat fuel or as part of a blend, and

    • (iv) meets the requirements set out in section 56.

Marginal note:Agreement to create credits

  •  (1) A registered creator may, before they have created any provisional compliance credits, enter into an agreement to create compliance credits for a compliance period

    • (a) with a person who is carrying out a CO2e-emission-reduction project described in section 30 or a person who is referred to in subsection 98(1), 99(1), 101(1), 102(1) or 104(1); or

    • (b) with a producer who is referred to in subsection 94(1), 95(1), 96(1) or 100(1), if the agreement applies only to the creation of compliance credits through the production of a quantity of low-carbon-intensity fuel in Canada.

  • Marginal note:Validity of agreement — requirements

    (2) The agreement is not valid unless it is signed by the authorized agents of each of the parties to the agreement and contains the following information:

    • (a) with respect to each party to the agreement,

      • (i) their name, civic address, postal address, telephone number and, if any, email address,

      • (ii) the name, title, civic address, postal address, telephone number and, if any, email address of their authorized agent, and

      • (iii) the name, title, civic address, postal address, telephone number and, if any, email address of a contact person, unless the contact person is the authorized agent;

    • (b) an indication of the compliance period to which the agreement relates;

    • (c) if the agreement relates to a CO2e-emission-reduction project described in section 30,

      • (i) the name of the facility at which the project is carried out or, if the equipment with which it is carried out is not within a facility, the name of that equipment,

      • (ii) the GPS coordinates to the fifth decimal place and, if any, civic address of that facility or equipment, and

      • (iii) an indication of the type of co-processed low-carbon-intensity fuel produced at the facility, if applicable;

    • (d) if the agreement relates to the production of the fuel referred to in subsection 94(1), 95(1), 96(1) or 100(1) in a facility, with respect to each facility where the fuel is produced,

      • (i) the name, GPS coordinates to the fifth decimal place and, if any, civic address of that facility, and

      • (ii) an indication of the type of fuel produced at the facility;

    • (e) if the agreement relates to the supply of a fuel referred to in subsection 98(1) or 99(1) at fuelling stations, with respect to each fuelling station,

      • (i) the name, GPS coordinates to the fifth decimal place and, if any, civic address of the fuelling station, and

      • (ii) an indication of the type of fuel supplied by the fuelling station;

    • (f) if the agreement is with a charging-network operator referred to in subsection 102(1), with respect to each charging station in the charging-network operator’s network,

      • (i) an indication of the province in which it is located, and

      • (ii) an indication of whether it is intended primarily for use by the occupants of a private dwelling-place, for use by the public or for another use;

    • (g) if the agreement is with a charging-site host referred to in subsection 101(1), with respect to each charging station that the charging-site host owns or leases,

      • (i) an indication of the province in which it is located, and

      • (ii) the name of the charging-network operator, if any, who operates the communication platform that collects data from the charging station; and

    • (h) if the agreement is with an owner or operator referred to in subsection 104(1) of one or more hydrogen fuelling stations, the name, GPS coordinates to the fifth decimal place and, if any, civic address of each fuelling station.

Marginal note:Submission to Minister

  •  (1) A registered creator who enters into an agreement referred to in section 21 must submit the agreement to the Minister and, subject to subsection (2), must not create provisional compliance credits under the agreement until the day after the day on which it is submitted.

  • Marginal note:Exception — submission within first 60 days

    (2) If the agreement is submitted to the Minister during the first 60 days of the compliance period to which the agreement relates, the registered creator may create provisional compliance credits under the agreement as of the first day of that compliance period unless the agreement provides for a later date.

Creation of Provisional Compliance Credits

Marginal note:Creation of provisional compliance credits

  •  (1) Any compliance credit created under subsection 19(1) or section 20 is considered to be a provisional compliance credit at the time that it is created.

  • Marginal note:No use of provisional credit

    (2) A primary supplier must not use a provisional compliance credit to satisfy a total reduction requirement or to comply with any of the volumetric requirements set out in subsections 6(1) and 7(1) and must not transfer a provisional compliance credit under the compliance-credit transfer system.

  • Marginal note:Single use for creation of provisional credits

    (3) A quantity of a fuel or an energy source that has been used by a person to create provisional compliance credits under subsection 94(1), 95(1), 96(1), 98(1), 99(1), 100(1), 101(1), 102(1) or 104(1) must not be used by another person to create compliance credits under the same subsection, and any quantity that is used more than once under the same subsection is deemed not to create any provisional compliance credits.

  • Marginal note:Loss of provisional status

    (4) A provisional compliance credit that is the subject of a credit-creation report submitted under section 120 or 121 ceases to be provisional when the Minister deposits it into a compliance-credit account under subsection 24(1) or (2).

  • Marginal note:Ownership of provisional credits

    (5) On creation, a provisional compliance credit is owned by the registered creator who created it.

  • Marginal note:Single owner

    (6) At any given time, a provisional compliance credit may only have a single owner.

Marginal note:Deposit into account

  •  (1) The compliance credits that are the subject of a credit-creation report submitted under section 120 or 121 must be deposited by the Minister as soon as feasible after the reception of the report into the registered creator’s account that was opened under

    • (a) paragraph 28(a), in the case of a compliance credit created under subsection 19(1); and

    • (b) paragraph 28(b), in the case of a compliance credit created under section 20.

  • Marginal note:Deposit — adjustment of credits

    (2) The compliance credits created under section 88, 89 or 90 that are the subject of a credit-creation report submitted under section 120 or a credit-adjustment report submitted under section 122 must be deposited by the Minister as soon as feasible after the reception of the report into any of the registered creator’s compliance-credit accounts opened under section 28.

  • Marginal note:Identification number

    (3) The Minister must assign an identification number to each compliance credit when it is deposited into a compliance-credit account.

Registration as Registered Creator

Marginal note:Registration report

  •  (1) A person who wishes to create compliance credits under subsection 19(1) or section 20 or under an agreement referred to in section 21 may register with the Minister as a registered creator by submitting to the Minister a registration report containing the information referred to in section 1 of Schedule 3 and any applicable information referred to in sections 4 to 12 of that Schedule.

  • Marginal note:Registration before creation

    (2) A registered creator must not create provisional compliance credits under subsection 19(1) or section 20 until the day after the day on which they become a registered creator.

  • Marginal note:Exception — registration within 60 days

    (3) However, a person who submits a registration report to the Minister during the period that begins on the day on which these Regulations are registered and ends 60 days after that day may create provisional compliance credits as of that day.

Marginal note:Change of information

  •  (1) If there are any changes in the information referred to in section 1 of Schedule 3 that is provided in the registration report, the registered creator must send a notice to the Minister that provides the updated information within 30 days after the day on which the change occurs.

  • Marginal note:Sections 4 to 12 of Schedule 3

    (2) If there are any changes in the information referred to in sections 4 to 12 of Schedule 3 that is provided in the registration report, the registered creator must send a notice to the Minister that provides the updated information no later than on the next day on which they are required to submit a report under subsection 120(1) or 121(1).

  • Marginal note:New agreement

    (3) A registered creator who enters into an agreement under section 21 must send a notice to the Minister that contains, in respect of the activities carried out by the person with whom they have entered into the agreement, the information referred to in section 1 of Schedule 3 and any applicable information referred to in sections 4 to 12 of that Schedule.

Marginal note:Cancellation of registration

  •  (1) A registered creator may cancel their registration as a registered creator if they

    • (a) send to the Minister a notice that indicates their intention to cancel their registration; and

    • (b) submit to the Minister any report or send any notice that they are required by these Regulations to submit or send.

  • Marginal note:Cancellation by Minister

    (2) If, after receiving the notice referred to in paragraph (1)(a), the Minister is satisfied that the registered creator has complied with these Regulations, the Minister must

    • (a) in the case of a registered creator who is not a primary supplier, cancel any compliance credits in any of the registered creator’s accounts opened under section 28;

    • (b) cancel the registered creator’s registration as a registered creator; and

    • (c) send a notice to the registered creator informing them that their registration is cancelled.

Compliance-Credit Accounts

Marginal note:Opening

 On the registration of a primary supplier under subsection 10(1) or a registered creator under subsection 25(1), the Minister must open the following accounts for the primary supplier or the registered creator in the compliance-credit transfer system:

  • (a) a liquid-fuel-compliance-credit account; and

  • (b) a gaseous-fuel-compliance-credit account.

Marginal note:Credit remains in account

 A compliance credit that is deposited into an account must remain in that account until the compliance credit is cancelled or transferred.

CO2e-Emission-Reduction Project

Marginal note:Series of activities

 A CO2e-emission-reduction project must consist of a series of activities that, when carried out, result in

  • (a) a reduction of the number of tonnes of CO2e emissions that are released during the activities carried out over the life cycle of a fossil fuel in the liquid state at standard conditions, including all emissions associated with the extraction of the hydrocarbons used to produce the fuel, with the processing, refining or upgrading of those hydrocarbons to produce the fuel, with the transportation or distribution of those hydrocarbons or the fuel and with the combustion of the fuel;

  • (b) the sequestration of any CO2e emissions that are released during the activities carried out over the life cycle of a fossil fuel in the liquid state at standard conditions, including all emissions associated with the extraction of the hydrocarbons used to produce the fuel, with the processing, refining or upgrading of those hydrocarbons to produce the fuel, with the transportation or distribution of those hydrocarbons or the fuel and with the combustion of the fuel;

  • (c) the use of any CO2e emissions that are released during the activities carried out over the life cycle of a fossil fuel in the liquid state at standard conditions, including all emissions associated with the extraction of the hydrocarbons used to produce the fuel, with processing, refining or upgrading those hydrocarbons to produce the fuel, with the transportation or distribution of those hydrocarbons or the fuel and with the combustion of the fuel; or

  • (d) the production of a quantity of co-processed low-carbon-intensity fuel to which may be attributed a reduction in the number of tonnes of CO2e that would otherwise have been emitted by the use of a fuel in the liquid class or gaseous class, if the co-processed low-carbon-intensity fuel

    • (i) is used or sold for use as a fuel in Canada whether as neat fuel or as part of a blend, and

    • (ii) meets the requirements set out in section 56.

Marginal note:Generic quantification method

  •  (1) The Minister may establish a generic emission-reduction quantification method that is applicable to any project for which no specific emission-reduction quantification method is applicable on the day on which the project is recognized under subsection 35(1) or 39(1).

  • Marginal note:Conditions

    (2) The generic emission-reduction quantification method must

    • (a) be consistent with ISO Standard 14064-2;

    • (b) establish a period of 10 years, beginning on the later of the day on which the Minister recognizes a project to which it is applicable and any preferred day referred to in paragraph 34(2)(b), at the end of which the carrying out of the project ceases to create compliance credits; and

    • (c) indicate that it is applicable to projects carried out in Canada or indicate that it is applicable to projects carried out in a specified foreign country or subdivision of a foreign country that has an agreement with Canada referred to in paragraph 39(1)(b).

Marginal note:Specific quantification method

  •  (1) The Minister may establish a specific emission-reduction quantification method that is applicable to a project of a specific type.

  • Marginal note:Conditions

    (2) The specific emission-reduction quantification method must

    • (a) be consistent with ISO Standard 14064-2;

    • (b) be based on data that are verifiable for a specified period

    • (c) be based on emission factors that are considered by generally recognized scientific sources

      • (i) to be appropriate for the quantification of the reduction, sequestration or use of CO2e emissions for the project, and

      • (ii) to not result in an overestimate of that quantification;

    • (d) establish a period of no less than 10 years, beginning on the later of the day on which the Minister recognizes the project and any preferred day referred to in paragraph 34(2)(b), at the end of which the carrying out of the project ceases to create compliance credits;

    • (e) identify the data that are necessary to determine the number of compliance credits created under paragraph 19(1)(a) or 20(a) by the carrying out of the project for a specified period; and

    • (f) indicate that it is applicable to projects carried out in Canada or indicate that it is applicable to projects carried out in a specified foreign country or subdivision of a foreign country that has an agreement with Canada referred to in paragraph 39(1)(b).

Marginal note:Exception

 Despite sections 31 and 32, no emission-reduction quantification method is applicable to, and no compliance credits are created under paragraph 19(1)(a) or 20(a) by any of the following types of projects:

  • (a) projects that include an operational or physical change that is solely for the purpose of reducing the production of fuel;

  • (b) projects that are maintenance activities;

  • (c) projects that include a reduction in the number of tonnes of CO2e emissions by displacing the use of a type of crude oil processed by a facility with the use of another type of crude oil;

  • (d) projects that consist of current practices that would be carried out in the ordinary course of business;

  • (e) projects that include a reduction in the number of tonnes of CO2e emissions that are released during the extraction of the hydrocarbons used to produce a fuel, during the processing, refining or upgrading of those hydrocarbons to produce the fuel, during the transportation or distribution of those hydrocarbons or the fuel and during the combustion of the fuel by displacing the use of that fuel with the use of fuel, hydrogen or electricity for which compliance credits may be created under any of sections 94, 96, 98 to 102 and 104.

Marginal note:Application for recognition

  •  (1) A registered creator may apply to the Minister for the recognition of a CO2e-emission-reduction project described in section 30 as a project that may create compliance credits when carried out in Canada.

  • Marginal note:Contents of application

    (2) The application must be signed by the authorized agent of the registered creator and contain

    • (a) the information referred to in Schedule 4;

    • (b) if the registered creator prefers that the carrying out of the project may create provisional compliance credits only as of a particular day, which must be no later than 18 months after the day on which the application is made, an indication of that preferred day; and

    • (c) an indication that the registered creator is applying to use a generic emission-reduction quantification method or a specific emission-reduction quantification method, whichever is applicable to the project, and the name of that method.

Marginal note:Recognition — generic quantification method

  •  (1) In the case of an application under subsection 34(1) for the recognition of a CO2e-emission-reduction project and the use of a generic emission-reduction quantification method that is applicable to the project, the Minister must recognize the project as a project that may create compliance credits when carried out if the Minister is satisfied, based on the information provided by the registered creator, that

    • (a) the activities that result in the reduction, sequestration or use of CO2e emissions will be carried out in Canada;

    • (b) the project’s reduction, sequestration or use of CO2e emissions will be determined using the generic emission-reduction quantification method;

    • (c) the activity specified in the generic emission-reduction quantification method that allows the project to begin to reduce, sequester or use CO2e emissions was or will be carried out on or after July 1, 2017;

    • (d) the specified activities that would have been carried out if not for the implementation of the project and the CO2e emissions that would have resulted from those activities, as well as the greenhouse gas sources and sinks that have been selected by the applicant to determine those CO2e emissions,

      • (i) are functionally equivalent to the project, in terms of the type and level of activity of products provided,

      • (ii) are in accordance with ISO Standard 14064-2 and with the generic emission-reduction quantification method, and

      • (iii) do not result in an overestimation of CO2e emissions resulting from those specified activities that would have been carried out by the applicant; and

    • (e) the greenhouse gas sources and sinks that have been selected by the applicant and are relevant to the project meet the following conditions:

      • (i) they are in accordance with ISO Standard 14064-2 and with the generic emission-reduction quantification method, and

      • (ii) they do not result in an underestimation of CO2e emissions released during the project.

  • Marginal note:Unique alphanumeric identifier

    (2) The Minister must assign a unique alphanumeric identifier to a CO2e-emission-reduction project recognized under subsection (1).

  • Marginal note:Number of compliance credits

    (3) The number of provisional compliance credits that are created for each compliance period by the carrying out of a project recognized under subsection (1) is determined — in accordance with the generic emission-reduction quantification method — based on the proportion of the quantity of crude oil or liquid fossil fuel that is not exported from Canada and that has a reduced carbon intensity as a result of the activities carried out for the project.

  • Marginal note:End of project

    (4) The carrying out of a project recognized under subsection (1) ceases to create compliance credits as of the end of the period referred to in paragraph 31(2)(b) or, if applicable, the end of the five-year period referred to in subsection 42(1).

Marginal note:Recognition — specific quantification method

  •  (1) In the case of an application under subsection 34(1) for the recognition of a CO2e-emission-reduction project and the use of a specific emission-reduction quantification method that is applicable to the project, the Minister must recognize the project as a project that may create compliance credits when carried out if the Minister is satisfied, based on the information provided to the Minister by the registered creator, that

    • (a) the activities that result in the reduction, sequestration or use of CO2e emissions will be carried out in Canada;

    • (b) the project’s reduction, sequestration or use of CO2e emissions will be determined using the specific emission-reduction quantification method; and

    • (c) the activity specified in the specific emission-reduction quantification method that allows the project to begin to reduce, sequester or use CO2e emissions was or will be carried out on or after July 1, 2017, unless the method provides that the activity may be carried out before that date.

  • Marginal note:Unique alphanumeric identifier

    (2) The Minister must assign a unique alphanumeric identifier to a CO2e-emission-reduction project recognized under subsection (1).

  • Marginal note:Number of compliance credits

    (3) The number of provisional compliance credits that are created for each compliance period by the carrying out of a project recognized under subsection (1) is determined — in accordance with the specific emission-reduction quantification method — based on the proportion of the quantity of crude oil or liquid fossil fuel that is not exported from Canada and that has a reduced carbon intensity as a result of the activities carried out for the project.

  • Marginal note:End of project

    (4) The carrying out of a project recognized under subsection (1) ceases to create compliance credits as of the end of the period referred to in paragraph 32(2)(d) or, if applicable, the end of the five-year period referred to in subsection 42(1).

Marginal note:Application for recognition — change of method

  •  (1) If, after the recognition of a CO2e-emission-reduction project under subsection 35(1) but before the end of the period referred to in paragraph 31(2)(b) or, if applicable, the five-year period referred to in subsection 42(1), the Minister establishes a specific emission-reduction quantification method under subsection 32(1) that is applicable to the project, the registered creator may apply to the Minister for the recognition of the project as a project that may create compliance credits when carried out in Canada using that method.

  • Marginal note:Contents of application

    (2) The application must be signed by the authorized agent of the registered creator and contain

    • (a) if the information contained in the original application for recognition under subsection 34(1), other than the information referred to in paragraph 2(d) of Schedule 4, has changed, the updated information;

    • (b) an indication that the registered creator is applying to use the specific emission-reduction quantification method and the name of that method;

    • (c) the information referred to in paragraph 2(d) of Schedule 4 in respect of that method; and

    • (d) if the registered creator prefers that the carrying out of the project may create provisional compliance credits only as of a particular day, an indication of that preferred day, which must be

      • (i) no later than 18 months after the day on which the application is made, and

      • (ii) before the end of the period referred to in paragraph 31(2)(b) or, if applicable, the five-year period referred to in subsection 42(1).

  • Marginal note:Recognition by the Minister

    (3) The Minister must recognize the CO2e-emission-reduction project as a project that may create compliance credits when carried out if the Minister is satisfied, based on the information provided by the registered creator, that the project meets the criteria set out in paragraphs 36(1)(a) to (c).

  • Marginal note:Unique alphanumeric identifier

    (4) The Minister must assign a unique alphanumeric identifier to a CO2e-emission-reduction project recognized under subsection (3).

  • Marginal note:Period — creation of compliance credits

    (5) Subject to subsection 42(4), the period during which the carrying out of the project may create provisional compliance credits begins on the later of the day on which it is recognized under subsection (3) and the preferred day referred to in paragraph (2)(d) and is determined by the formula

    S − D

    where

    S
    is the period referred to in paragraph 32(2)(d) and established in the specific emission-reduction quantification method that is applicable to the project, expressed as a number of days; and
    D
    is the number of days — during the period referred to in paragraph 31(2)(b) — on which the carrying out of the project has created provisional compliance credits using the generic emission-reduction quantification method.
  • Marginal note:Number of compliance credits

    (6) The number of provisional compliance credits that are created for the period determined under subsection (5) or, if applicable, subsection 42(4) by the carrying out of a project that is recognized under subsection (3) is determined — in accordance with the specific emission-reduction quantification method — based on the proportion of the quantity of crude oil or liquid fossil fuel that is not exported from Canada and that has a reduced carbon intensity as a result of the activities carried out for the project.

  • Marginal note:End of project — generic method

    (7) The carrying out of a project that is recognized under subsection (3) ceases to create compliance credits under section 35 as of the day before the day on which the period determined under subsection (5) begins.

  • Marginal note:End of project — specific method

    (8) The carrying out of a project that is recognized under subsection (3) ceases to create compliance credits under subsection (6) as of the end of the period determined under subsection (5) or, if applicable, the end of the five-year period referred to in subsection 42(1).

Marginal note:Application for recognition — project in foreign country

  •  (1) A registered creator may apply to the Minister for the recognition of a CO2e-emission-reduction project that is described in section 30 and carried out in a foreign country or subdivision of a foreign country as a project that may create compliance credits when carried out in the foreign country or subdivision, if there is an agreement referred to in paragraph 39(1)(b) between Canada and that foreign country or subdivision and the agreement is applicable to that type of project.

  • Marginal note:Contents of application

    (2) The application must be signed by the authorized agent of the registered creator and must contain

    • (a) the information referred to in Schedule 4;

    • (b) if the registered creator prefers that the carrying out of the project may create provisional compliance credits only as of a particular day, which must be no later than 18 months after the day on which the application is made, an indication of that preferred day; and

    • (c) an indication that the registered creator is applying to use the applicable generic emission-reduction quantification method or specific emission-reduction quantification method that is indicated in the agreement referred to in subsection (1) and the name of that method.

Marginal note:Recognition — project in foreign country

  •  (1) The Minister must recognize a CO2e-emission-reduction project carried out in a foreign country or subdivision of a foreign country as a project that may create compliance credits when carried out if the Minister is satisfied that

    • (a) based on the information provided to the Minister by the registered creator, the project meets the criteria set out in subsection (2) or (3), as the case may be; and

    • (b) Canada has an agreement with the foreign country or the subdivision that meets the requirements set out in subsection (4).

  • Marginal note:Generic quantification method

    (2) In the case of an application under subsection 38(1) for the recognition of a CO2e-emission-reduction project and the use of a generic emission-reduction quantification method that is applicable to the project, the project must meet the following criteria:

    • (a) the activities carried out outside Canada during the project that result in the reduction, sequestration or use of CO2e emissions are comparable in effectiveness with projects that are carried out in Canada with respect to the reduction, sequestration or use of CO2e emissions released during the activities carried out over the life cycle of a fossil fuel that is in the liquid state at standard conditions;

    • (b) the activity specified in the generic emission-reduction quantification method that allows the project to begin to reduce, sequester or use CO2e emissions was or will be carried out on or after July 1, 2017;

    • (c) the reduction, sequestration or use of CO2e emissions resulting from the project is determined using the generic emission-reduction quantification method;

    • (d) the specified activities that would have been carried out if not for the implementation of the project and the CO2e emissions that would have resulted from those activities, as well as the greenhouse gas sources and sinks that have been selected by the applicant to determine those CO2e emissions,

      • (i) are functionally equivalent to the project, in terms of the type and level of activity of products provided,

      • (ii) are in accordance with ISO Standard 14064-2 and with the generic emission-reduction quantification method, and

      • (iii) do not result in an overestimation of CO2e emissions resulting from those specified activities that would have been carried out by the applicant; and

    • (e) the greenhouse gas sources and sinks that have been selected by the applicant and are relevant to the project meet the following conditions:

      • (i) they are in accordance with ISO Standard 14064-2 and with the generic emission-reduction quantification method, and

      • (ii) they do not result in an underestimation of CO2e emissions released during the project.

  • Marginal note:Specific quantification method

    (3) In the case of an application under subsection 38(1) for the recognition of a CO2e-emission-reduction project and the use of a specific emission-reduction quantification method that is applicable to the project, the project must meet the following criteria:

    • (a) the activities carried out outside Canada during the project that result in the reduction, sequestration or use of CO2e emissions are comparable in effectiveness with projects that are carried out in Canada with respect to the reduction, sequestration or use of CO2e emissions released during the activities carried out over the life cycle of a fossil fuel that is in the liquid state at standard conditions;

    • (b) the activity specified in the specific emission-reduction quantification method that allows the project to begin to reduce, sequester or use CO2e emissions was or will be carried out on or after July 1, 2017, unless the method provides that the activity may be carried out before that date; and

    • (c) the reduction, sequestration or use of CO2e emissions resulting from the project is determined using the specific emission-reduction quantification method.

  • Marginal note:Agreement with foreign country or subdivision

    (4) An agreement referred to in paragraph (1)(b) with a foreign country or a subdivision of a foreign country must

    • (a) specify any generic emission-reduction quantification methods and specific emission-reduction quantification methods that are applicable to projects of specific types that are carried out in the foreign country or subdivision;

    • (b) recognize that the emission reductions that result from those specific types of projects do not result from current practices that would be carried out in the ordinary course of business;

    • (c) recognize that the emission reductions that result from those specific types of projects are permanent;

    • (d) recognize that there are environmental laws that are in force in, and enforceable by, the foreign country or the subdivision that are applicable to those specific types of projects and that are comparable to environmental laws in force in Canada in terms of effectiveness;

    • (e) recognize that there are laws related to the requirement set out in paragraph (c) that are in force in, and enforceable by, the foreign country or the subdivision and that are comparable to environmental laws in force in Canada in terms of effectiveness;

    • (f) set out how the foreign country or the subdivision will carry out enforcement activities, including the conduct of inspections, compliance verifications and investigations of suspected violations, and how it will enforce compliance with the laws referred to in paragraphs (d) and (e) in a manner that is equivalent to the level of enforcement in Canada; and

    • (g) set out how the foreign country or the subdivision will cooperate and share information with Canada to assist in the administration and enforcement of these Regulations.

  • Marginal note:Unique alphanumeric identifier

    (5) The Minister must assign a unique alphanumeric identifier to a CO2e-emission-reduction project recognized under subsection (1).

  • Marginal note:End of project

    (6) The carrying out of a project that is recognized under subsection (1) ceases to create compliance credits under section 41 on the earlier of

    • (a) the end of the period referred to in paragraph 31(2)(b) or, if applicable, the end the five-year period referred to in subsection 42(1), and

    • (b) the day on which Canada no longer has an agreement with the foreign country or subdivision of a foreign country in which the project is carried out.

Marginal note:Application for recognition — change of method

  •  (1) If, after the recognition of a CO2e-emission-reduction project under subsection 39(1) as a project that may create compliance credits using a generic emission-reduction quantification method, but before the end of the period referred to in paragraph 31(2)(b) or, if applicable, the five-year period referred to in subsection 42(1), the Minister establishes a specific emission-reduction quantification method under subsection 32(1) that is applicable to the project and the agreement referred to in paragraph 39(1)(b) is amended to permit the use of that specific emission-reduction quantification method for that type of project, the registered creator may apply to the Minister for the recognition of the project as a project that may create compliance credits when carried out using that specific emission-reduction quantification method.

  • Marginal note:Contents of application

    (2) The application must be signed by the authorized agent of the registered creator and must contain

    • (a) if the information contained in the original application for recognition of the project under subsection 38(1), other than the information referred to in paragraph 2(d) of Schedule 4, has changed, the updated information;

    • (b) an indication that the registered creator is applying to use the specific emission-reduction quantification method and the name of that method;

    • (c) the information referred to in paragraph 2(d) of Schedule 4 in respect of that method; and

    • (d) if the registered creator prefers that the carrying out of the project may create provisional compliance credits only as of a particular day, an indication of the preferred day, which must be

      • (i) no later than 18 months after the day on which the application is made, and

      • (ii) before the end of the period referred to in paragraph 31(2)(b) or , if applicable, the five-year period referred to in subsection 42(1).

  • Marginal note:Recognition by the Minister

    (3) The Minister must recognize the CO2e-emission-reduction project as a project that may create compliance credits when carried out if the Minister is satisfied, based on the information provided by the registered creator, that the project meets the criteria set out in paragraph 39(1)(b) and subsection 39(3).

  • Marginal note:Unique alphanumeric identifier

    (4) The Minister must assign a unique alphanumeric identifier to a CO2e-emission-reduction project recognized under subsection (3).

  • Marginal note:Creation of compliance credits

    (5) Subject to subsection 42(4), the period during which the carrying out of the project may create provisional compliance credits begins on the later of the day on which the project is recognized under subsection (3) and the preferred day referred to in paragraph (2)(d) and is determined by the formula

    S − D

    where

    S
    is the period referred to in paragraph 32(2)(d) and established in the specific emission-reduction quantification method that is indicated in the agreement referred to in paragraph 39(1)(b) and that is applicable to the project, expressed as a number of days; and
    D
    is the number of days — during the period referred to in paragraph 31(2)(b) — on which the carrying out of the project has created provisional compliance credits using the generic emission-reduction quantification method.
  • Marginal note:End of project — generic method

    (6) The carrying out of a CO2e-emission-reduction project that is recognized under subsection (3) ceases to create compliance credits under section 39 on the earlier of

    • (a) the day before the day on which the period determined under subsection (5) begins, and

    • (b) the day on which Canada no longer has an agreement with the foreign country or subdivision of a foreign country in which the project is carried out.

  • Marginal note:End of project — specific method

    (7) The carrying out of a project that is recognized under subsection (3) ceases to create compliance credits under section 41 as of the end of the period determined under subsection (5) or, if applicable, the end of the five-year period referred to in subsection 42(1).

Marginal note:Number of compliance credits — projects in foreign country

 The number of provisional compliance credits that are created by the carrying out of a CO2e-emission-reduction project recognized under subsection 39(1) or 40(3) is determined — in accordance with the emission-reduction quantification method that is indicated in the agreement referred to in paragraph 39(1)(b) and that is applicable to the project — based on the proportion of the quantity of crude oil or liquid fossil fuel that is imported into Canada and that has a reduced carbon intensity as a result of the activities carried out for the project.

Marginal note:Extension of period — five years

  •  (1) Subject to subsection (3), during the year that precedes the end of the period referred to in paragraph 31(2)(b) or 32(2)(d) or determined under subsection 37(5) or 40(5), as the case may be, a registered creator may apply to the Minister to extend that period for a single period of five years.

  • Marginal note:Application — contents

    (2) The application for extension must be signed by the authorized agent of the registered creator and, if there are any changes in the information provided in the original application for recognition of the CO2e-emission-reduction project, the application for extension must provide the updated information.

  • Marginal note:No extension

    (3) In the case of a CO2e-emission-reduction project that was recognized under subsection 35(1) or 39(1) as a project that may create compliance credits when carried out using a generic emission-reduction quantification method, no application for extension may be made if, during the year that precedes the end of the period established under paragraph 31(2)(b), the Minister establishes a specific emission-reduction quantification method under subsection 32(1) that is applicable to the project.

  • Marginal note:Extension after change of method

    (4) If, during the five-year extension period granted by the Minister in respect of a CO2e-emission-reduction project that was recognized under subsection 35(1) or 39(1) as a project that may create compliance credits when carried out using a generic emission-reduction quantification method, the Minister recognizes the project under subsection 37(3) or 40(3) as a project that may create compliance credits when carried out using a specific emission-reduction quantification method, the period during which the project may create provisional compliance credits begins on the later of the day on which the project is recognized under subsection 37(3) or 40(3) and the preferred day referred to in paragraph 37(2)(d) or 40(2)(d), as the case may be, and is determined by the formula

    P − D

    where

    P
    is the five-year extension period granted by the Minister, expressed as a number of days; and
    D
    is the number of days — during the period P — on which the carrying out of the project has created provisional compliance credits using the generic emission-reduction quantification method.

Marginal note:Federal or provincial laws

 If an activity that is carried out as part of a CO2e-emission-reduction project ceases to be additional to what is required by the laws of Canada or of a province — other than any laws relating to greenhouse gas emission pricing mechanisms, the reduction of the carbon intensity of fuel or the use of low-carbon-intensity fuel — the number of provisional compliance credits that are created under subsections 35(3), 36(3) and 37(6) and section 41 by the carrying out of the project is reduced in proportion to the reduction of CO2e emissions that results from that activity.

Marginal note:Failure to comply with record requirements

 If a registered creator fails to comply with any of the requirements set out in sections 166 and 168 in relation to a CO2e-emission-reduction project, any compliance credits that are created by carrying out the project during the period of non-conformity with those requirements are not valid and are considered to be excess compliance credits that may be suspended by the Minister under section 158 or cancelled by the Minister under section 160.

Displacement of Fossil Fuel Usage

Land-Use and Biodiversity Criteria for Low-Carbon-Intensity Fuels

Marginal note:Maximum quantity

  •  (1) The maximum quantity of a low-carbon-intensity fuel that is produced at a facility by a producer in Canada or foreign supplier during each period referred to in subsection (3) for which compliance credits may be created by the carrying out of a CO2e-emission-reduction project described in paragraph 30(d) or be created under any of sections 94 to 96, 99, 100 and 104 is determined by the formula

    Qfuel x Qeligible ÷ (Qeligible + Qineligible)

    where

    Qfuel
    is the quantity of the low-carbon-intensity fuel that is produced at the facility during the period, expressed in kilograms or cubic metres, as applicable;
    Qeligible
    is the quantity of eligible feedstock that meets the requirements set out in section 47 that was used at the facility by the producer in Canada or foreign supplier to produce the low-carbon-intensity fuel during the period, expressed in kilograms or cubic metres, as applicable; and
    Qineligible
    is the quantity of feedstock, other than eligible feedstock, that was used at the facility by the producer in Canada or foreign supplier to produce the low-carbon-intensity fuel during the period, expressed in kilograms or cubic metres, as applicable.
  • Marginal note:Carbon intensity

    (2) For the purposes of subsection (1), a low-carbon-intensity fuel is a fuel that

    • (a) has a carbon intensity to which an alphanumeric identifier has been assigned under subsection 85(2); or

    • (b) has the default carbon intensity referred to in paragraph 75(1)(a) or determined in accordance with the emission-reduction quantification method that is applicable to a project described in paragraph 30(d).

  • Marginal note:Periods

    (3) The periods for producing low-carbon-intensity fuels are, for any compliance period that ends after January 1, 2024,

    • (a) the period beginning on the January 1 and ending on the March 31 of the compliance period;

    • (b) the period beginning on the April 1 and ending on the June 30 of the compliance period;

    • (c) the period beginning on the July 1 and ending on the September 30 of the compliance period; and

    • (d) the period beginning on the October 1 and ending on the December 31 of the compliance period.

  • Marginal note:Exclusive use

    (4) A person who uses a quantity of low-carbon-intensity fuel produced from an eligible feedstock to create credits in a jurisdiction outside Canada or to comply with a requirement relating to greenhouse gas emissions that is set by a jurisdiction outside Canada must not use that quantity of low-carbon-intensity fuel to create compliance credits by the carrying out of a CO2e-emission-reduction project referred to in paragraph 30(d) or under any of sections 94 to 96, 99, 100 and 104.

Marginal note:Eligibility requirements

  •  (1) Subject to subsection (2) and sections 48 to 55, 57 and 58, the following feedstock is eligible:

    • (a) feedstock that is not derived from biomass;

    • (b) feedstock that is derived from

      • (i) forest biomass derived from fire prevention and protection activities or from clearing activities that are not related to harvesting, such as infrastructure installation, pest and disease control and road maintenance,

      • (ii) crop residues or damaged crops,

      • (iii) secondary forest residues that are by-products of industrial wood-processing operations,

      • (iv) used or inedible organics from a residential area, retail store, restaurant, caterer or food processing plant,

      • (v) used fat or used vegetable oil,

      • (vi) used animal litter,

      • (vii) animal materials, including manure,

      • (viii) industrial effluents,

      • (ix) municipal wastewater, or

      • (x) used construction or demolition materials; and

    • (c) feedstock that is derived from agricultural or forest biomass but is not derived from a material or source referred to in paragraph (b).

  • Marginal note:Intentionally used feedstock

    (2) A feedstock that is derived from agricultural or forest biomass and that is intentionally altered in order to meet any of the conditions set out in paragraph (1)(b) is considered not to be an eligible feedstock for the purposes of that paragraph.

Marginal note:Quantity of eligible feedstock

  •  (1) The quantity of an eligible feedstock of a particular type that, after December 31, 2023, is removed from the site where it was harvested, mixed, processed, divided or obtained must not be greater than the quantity determined by the formula

    Qinventory + Qincoming

    where

    Qinventory
    is the quantity of eligible feedstock of that type that was at the site after the previous time that a quantity of eligible feedstock of that type was removed from the site, expressed in kilograms or cubic metres, as applicable; and
    Qincoming
    is the quantity of eligible feedstock of that type that was harvested at or brought to the site since the previous time that a quantity of eligible feedstock of that type was removed from the site, expressed in kilograms or cubic metres, as applicable.
  • Marginal note:Production of fuel

    (2) For each period referred to in subsection 45(3), the total of the quantity of eligible feedstock of a particular type that is used to produce a low-carbon-intensity fuel at a facility and the quantity of eligible feedstock of that type that is at the facility at the end of the period must not be greater than the quantity determined by the formula

    Qinventory + Qincoming

    where

    Qinventory
    is the quantity of eligible feedstock of that type that was at the facility at the beginning of the period, expressed in kilograms or cubic metres, as applicable; and
    Qincoming
    is the quantity of eligible feedstock of that type that was brought to the facility during the period, expressed in kilograms or cubic metres, as applicable.

Marginal note:Wildlife habitat

  •  (1) It is not permitted to harvest feedstock referred to in paragraph 46(1)(c) from land located in an area that provides a habitat for any rare, vulnerable or threatened species.

  • Marginal note:Exception

    (2) However, the Minister may, on application from a person who harvests a feedstock referred to in paragraph 46(1)(c) or who produces fuel from that feedstock, authorize the use of a feedstock obtained from rehabilitation or habitat-improvement activities carried out on land located in an area that provides a habitat referred to in subsection (1) if the Minister is satisfied that those activities do not adversely affect that habitat.

  • Marginal note:Application

    (3) The application must

    • (a) describe the activities that the person who harvests the feedstock has carried out or intends to carry out in the area; and

    • (b) demonstrate that the activities will not adversely affect the habitat.

Marginal note:Damaging agents

 A feedstock referred to in paragraph 46(1)(c) must be harvested and transported in accordance with measures that monitor, prevent and control the introduction, spread and establishment of damaging agents, such as pests, invasive species and disease.

Marginal note:Crops — indirect changes to land use

  •  (1) A feedstock referred to in any of subparagraphs 46(1)(b)(ii) to (vi) or paragraph 46(1)(c) that is a crop, crop by-product or crop residue must be produced in a manner that does not create a high risk of an indirect change to land use that adversely affects the environment.

  • Marginal note:European Commission Delegated Regulation

    (2) For the purposes of subsection (1), there is a high risk that the production of a feedstock will cause an indirect change to land use that adversely affects the environment if the value specified for that feedstock in the Annex to the Commission Delegated Regulation (EU) 2019/807 of 13 March 2019 is greater than

    • (a) 1% in the column entitled “Average annual expansion of production area since 2008 (%)”; and

    • (b) 10% in the column entitled “Share of expansion into land referred to in Article 29(4)(b) and (c) of Directive (EU) 2018/2001”.

Marginal note:Crops — excluded land

  •  (1) It is not permitted to harvest feedstock referred to in paragraph 46(1)(c) that is a crop from land that

    • (a) has an area greater than 1 ha and was, at any time on or after July 1, 2020,

      • (i) a forest that contains trees that are or are capable of reaching a height of 5 m and provide or are capable of providing a canopy cover of more than 10%,

      • (ii) a wetland that is periodically saturated with water for a period that is long enough to promote biological activity that is adapted to a wet environment, or

      • (iii) a grassland that is dominated by herbaceous or shrub vegetation that has not been cultivated for 10 years or more; or

    • (b) was never cultivated before July 1, 2020 and was, at any time on or after that day, in a riparian zone.

  • Marginal note:Definition of riparian zone

    (2) In subsection (1), riparian zone means land that is located within 30 m, measured on a slope distance following the topography of the land, of

    • (a) the high-water mark of a watercourse that is more than 3 m wide; or

    • (b) the shores of a lake or permanent wetland that has an area greater than 5 ha. 

Marginal note:Forest-based feedstock

 The harvesting of any feedstock referred to in paragraph 46(1)(c) that is derived from forest biomass must be carried out in accordance with a forest management plan that meets the following requirements:

  • (a) it must be possible for a verification body to evaluate it;

  • (b) it must be implemented, monitored and kept up to date, based on monitoring results, to promote adaptive management, by the person who is responsible for harvesting the feedstock; and

  • (c) it must specify the practices to be followed to ensure that

    • (i) the management of the land where the feedstock is harvested is carried out in a manner that promotes timely forest regeneration of that land to its pre-harvesting condition using species of trees that are ecologically suited to the site and drawn, if possible, from native species or local genotypes,

    • (ii) adverse effects are prevented on naturally regenerated stands containing multi-layered canopies with trees near their maximum longevity as well as standing and fallen dead trees and forest debris at varying stages of decomposition,

    • (iii) forest management and related activities in the areas where the feedstock is harvested are carried out in a manner that prevents or mitigates adverse effects on the quantity and quality of the soil, on the quantity and quality of surface and ground water resources and on biodiversity, and

    • (iv) forest management and related activities in the areas where the feedstock is harvested are carried out in a manner that maintains the connectivity of watercourses.

Marginal note:Exemption — approval by EPA

  •  (1) The Minister may exempt a feedstock that is a crop from the application of section 51 if

    • (a) the country from which the feedstock originates is the United States or is a country that is covered by the aggregate compliance approach referred to in section 80.1457 of Subchapter C of Chapter I of Title 40 of the United States Code of Federal Regulations; and

    • (b) the Minister is satisfied that section 80.1457 of Subchapter C of Chapter I of Title 40 of the United States Code of Federal Regulations provides a sufficient level of environmental protection with respect to the land on which the feedstock is harvested.

  • Marginal note:Effective date of exemption

    (2) The exemption takes effect, in the case of the United States, on the day on which this section comes into force or, in the case of any other country, on the later of

    • (a) the day on which the EPA decides that the country is covered by the aggregate compliance approach, and

    • (b) the day on which this section comes into force.

  • Marginal note:Period of validity

    (3) The exemption ceases to be valid on the earlier of

    • (a) in the case of the United States, the day on which the EPA publishes a finding that the 2007 baseline amount of agricultural land in the United States has been exceeded or, in the case of any other country, the day on which the EPA withdraws its approval for that country to be covered by the aggregate compliance approach, and

    • (b) the day on which the Minister determines that, following the granting of the exemption, amendments have been made to section 80.1457 of Subchapter C of Chapter I of Title 40 of the United States Code of Federal Regulations and, taking into account those amendments, the Minister is no longer satisfied that there is a sufficient level of environmental protection with respect to the land on which the feedstock is harvested.

Marginal note:Exemption — no net expansion

  •  (1) The Minister may, on application from the national level of government of a country, exempt a feedstock that is a crop from the application of section 51 if the Minister is satisfied that the country from which the feedstock originates has not, since July 1, 2020, undergone a net expansion of agricultural land, taking into account the following factors:

    • (a) any net expansion since July 1, 2020 to the national borders within which agricultural land is measured;

    • (b) the total amount of land within those national borders that was agricultural land on July 1, 2020;

    • (c) data from the preceding year on the harvesting of land, including satellite data, aerial photography, census data and agricultural survey data;

    • (d) data on the use of land to harvest crops between July 1, 2020 and the beginning of the preceding year, including satellite data, aerial photography, census data and agricultural survey data;

    • (e) any factors that have had or may have an effect on the use of agricultural land within those national borders, including agricultural practices, economic considerations and the content, efficacy and enforcement of applicable laws;

    • (f) the method of identifying which entity will gather and analyze data and submit it to the Minister, as well as the reliability and credibility of that entity;

    • (g) evidence with respect to whether the data and methods used to evaluate the net expansion of agricultural land are reliable and transparent;

    • (h) any comments from the public that the Minister receives; and

    • (i) any information that is necessary to determine whether the country from which the feedstock originates has, since July 1, 2020, undergone a net expansion of agricultural land.

  • Marginal note:Conditions

    (2) The exemption must not be granted by the Minister unless

    • (a) the national level of government of the country from which the feedstock originates has provided to the Minister, in English or French, information in respect of the factors referred to in paragraphs (1)(a) to (g) and (i);

    • (b) the national level of government of the country from which the feedstock originates has provided to the Minister a letter, in English or French, that is signed by an individual with a role comparable to a Minister who is responsible for the part of the government with primary expertise in agricultural land-use patterns and agricultural practices, data and statistics and, in the letter, the individual confirms that

      • (i) all supporting data for the factors referred to in paragraphs (1)(a) to (g) and (i) have been reviewed by that part of the government, and

      • (ii) the data supports the conclusion that the country from which the feedstock originates has not, since July 1, 2020, undergone a net expansion of agricultural land; and

    • (c) information in respect of the factors referred to in paragraphs (1)(a) to (g) and (i) has been published on the Department of the Environment’s website and the public has been given an opportunity to submit comments with respect to that information and the proposed exemption for a period of at least 60 days.

  • Marginal note:Period of validity

    (3) The exemption takes effect on the day on which it is granted and ceases to be valid one year after that day, unless the Minister grants a subsequent exemption under subsection (1).

  • Marginal note:Publication

    (4) The Minister must publish on the Department of the Environment’s website, for each exemption that is granted under subsection (1) with respect to a feedstock, a notice of the exemption that sets out the name of the country from which the feedstock originates and the date on which the exemption takes effect.

Marginal note:Exemption — other laws

  •  (1) The Minister may, on application from a national or subnational level of government of a country, exempt a feedstock that originates from that country from the application of subsection 48(1), section 49 or subparagraph 52(c)(i), (ii), (iii) or (iv) if the Minister is satisfied that the feedstock is

    • (a) in the case of subsection 48(1), subject to laws that effectively prohibit the harvesting of the feedstock in any area that provides a habitat for any rare, vulnerable or threatened species;

    • (b) in the case of section 49, subject to laws that effectively require it to be harvested and transported in accordance with measures to monitor, prevent and control the introduction, spread and establishment of damaging agents, such as pests, invasive species and disease;

    • (c) in the case of subparagraph 52(c)(i), subject to laws that

      • (i) effectively promote timely forest regeneration of the land where the feedstock is harvested to its pre-harvesting condition using species of trees that are ecologically suited to the site and drawn, if possible, from native species or local genotypes, and

      • (ii) include enforcement requirements for forest regeneration on the land where the feedstock is harvested;

    • (d) in the case of subparagraph 52(c)(ii), subject to laws that

      • (i) effectively prevent adverse effects on naturally regenerating stands containing multi-layered canopies with trees near their maximum longevity as well as standing and fallen dead trees and forest debris at varying stages of decomposition, and

      • (ii) include enforcement requirements for the purpose of protecting stands described in subparagraph 52(c)(ii);

    • (e) in the case of subparagraph 52(c)(iii) as it relates to soil, subject to laws that

      • (i) effectively require that forest management and related activities be carried out on the land where the feedstock is harvested in a manner that prevents adverse effects on the quantity and quality of the soil and mitigates any adverse effects that do occur, and

      • (ii) include enforcement requirements for the purpose of preventing adverse effects on the quantity and quality of the soil;

    • (f) in the case of subparagraph 52(c)(iii) as it relates to surface and ground water resources, subject to laws that

      • (i) effectively require that forest management and related activities be carried out on the land where the feedstock is harvested in a manner that prevents adverse effects on the quantity and quality of surface and ground water resources and mitigates any adverse effects that do occur, and

      • (ii) include enforcement requirements for the purpose of preventing adverse effects on the quantity and quality of surface and ground water resources;

    • (g) in the case of subparagraph 52(c)(iii) as it relates to biodiversity, subject to laws that

      • (i) effectively require that forest management and related activities be carried out on the land where the feedstock is harvested in a manner that prevents adverse effects on biodiversity and mitigates any adverse effects that do occur, and

      • (ii) include enforcement requirements for the purpose of preventing adverse effects on biodiversity; and

    • (h) in the case of subparagraph 52(c)(iv), subject to laws that

      • (i) effectively require that forest management and related activities be carried out on the land where the feedstock is harvested in a manner that maintains the connectivity of watercourses, and

      • (ii) include enforcement requirements for the purpose of maintaining the connectivity of watercourses.

  • Marginal note:Language of documents

    (2) Any information or document that is relevant to the Minister’s decision regarding whether to exempt a feedstock under subsection (1) must be provided to the Minister in English or French.

  • Marginal note:Period of validity

    (3) An exemption granted under subsection (1) ceases to be valid on the ier of

    • (a) the day that is seven years after the day on which the exemption is granted by the Minister, and

    • (b) the day on which the Minister determines that, following the granting of the exemption, amendments have been made to the laws applicable to the exempted feedstock and, taking into account such amendments, the Minister is no longer satisfied that the laws meet the conditions referred to in subsection (1).

  • Marginal note:Publication

    (4) The Minister must publish on the Department of the Environment’s website, for each exemption that is granted under subsection (1) with respect to a feedstock, a notice of the exemption that sets out the title of the laws to which the feedstock is subject and the date on which the exemption takes effect.

Marginal note:Low-carbon-intensity fuel

 A person must not use a quantity of low-carbon-intensity fuel to create compliance credits by carrying out a CO2e-emission-reduction project described in paragraph 30(d) or to create compliance credits under any of sections 94 to 96, 99, 100 and 104, unless

  • (a) the fuel is produced from a quantity of an eligible feedstock that is referred to in paragraph 46(1)(a) and the conditions set out in subsection 57(1) are met in respect of the feedstock; or

  • (b) the fuel is produced from a quantity of an eligible feedstock that is referred to in paragraph 46(1)(b) or (c), the conditions set out in subsection 57(2) are met in respect of the feedstock and the registered creator who produced the fuel or the foreign supplier ensures that, for each period referred to in subsection 45(3), the quantity of the eligible feedstock that is used at each of their facilities to produce the fuel is less than or equal to the quantity determined by the formula set out in subsection 47(2).

Marginal note:Producer or importer — paragraph 46(1)(a)

  •  (1) A feedstock referred to in paragraph 46(1)(a) is not eligible unless

    • (a) the registered creator ensures that any person who produces a low-carbon-intensity fuel using the feedstock retains the following records:

      • (i) delivery records, contracts and invoices with respect to each quantity of the feedstock that is brought to any of their facilities,

      • (ii) sales records for all low-carbon-intensity fuel, other than co-processed low-carbon-intensity fuel, that was produced using all or any portion of a quantity of the feedstock, and

      • (iii) records for all co-processed low-carbon-intensity fuel that demonstrate that it was produced using all or any portion of a quantity of eligible feedstock; and

    • (b) the registered creator who imports into Canada a quantity of a low-carbon-intensity fuel produced using the feedstock retains the following records with respect the quantity of low-carbon-intensity fuel:

      • (i) delivery records, contracts and invoices, and

      • (ii) sales records.

  • Marginal note:Eligibility — paragraph 46(1)(b) or (c)

    (2) A feedstock referred to in paragraph 46(1)(b) or (c) is not eligible unless

    • (a) declarations are made by the following persons in accordance with any of subsections 58(1) to (4) at least once every year:

      • (i) every person who possesses all or any portion of a quantity of the feedstock when it is mixed with another quantity of any feedstock,

      • (ii) every person who possesses all or any portion of a quantity of the feedstock when it is processed,

      • (iii) every person who possesses all or any portion of a quantity of the feedstock when it is divided into multiple portions,

      • (iv) the person who is responsible for obtaining all or any portion of a quantity of the feedstock from its first point of use or disposal, in the case of a feedstock referred to in paragraph 46(1)(b), and

      • (v) the person who is responsible for harvesting all or any portion of a quantity of the feedstock, in the case of a feedstock referred to in paragraph 46(1)(c);

    • (b) the registered creator or foreign supplier ensures that any person who harvests, mixes, processes, divides or obtains all or any portion of a quantity of the feedstock retains

      • (i) the declaration that they made under paragraph (a),

      • (ii) a copy of the declaration made under paragraph (a), if any, by the person who possessed that quantity immediately before they did, and

      • (iii) records that establish the quantity of the feedstock that enters and is removed from the site where it is harvested, mixed, processed, divided or obtained;

    • (c) the registered creator or foreign supplier retains records in accordance with subsection 59(1);

    • (d) the registered creator who imports into Canada a low-carbon-intensity fuel that was produced using the feedstock retains records in accordance with subsection 59(2); and

    • (e) the registered creator or foreign supplier has a methodology in place to determine whether, each time a quantity of the feedstock is removed from the site where it is harvested, mixed, processed, divided or obtained, the quantity that is removed from the site is less than or equal to the quantity determined by the formula set out in subsection 47(1).

Marginal note:Declaration by harvester

  •  (1) A declaration made by a person referred to in subparagraph 57(2)(a)(v) must contain the following information:

    • (a) their name, civic address, postal address, telephone number and, if any, email address;

    • (b) if an authorized agent is making the declaration on behalf of the person, the name, civic address, postal address, telephone number and, if any, email address of the authorized agent;

    • (c) the GPS coordinates to the fifth decimal place and, if any, civic address of the site where the feedstock that is the subject of the declaration was harvested;

    • (d) an indication of whether any part of that site is on land referred to in subsection 48(1) and, if so, confirmation that they have a record of the Minister’s authorization under subsection 48(2);

    • (e) if the feedstock is sold, the name and civic and postal address of the person to whom it is sold;

    • (f) the type of the feedstock;

    • (g) the quantity of the feedstock that is sold, expressed in kilograms or cubic metres, as applicable;

    • (h) a confirmation that the requirements set out in section 48 are met with respect to the feedstock or that the feedstock is the subject of an exemption granted under paragraph 55(1)(a);

    • (i) a confirmation that the requirements set out in section 49 are met with respect to the feedstock or that feedstock is the subject of an exemption granted under paragraph 55(1)(b);

    • (j) if the feedstock is a crop, a confirmation that it was not harvested on land described in section 51 or is the subject of an exemption granted under subsection 53(1) or 54(1);

    • (k) if the feedstock is derived from forest biomass, a confirmation that

      • (i) it was harvested in accordance with the requirements set out in paragraph 52(c)(i) or is the subject of an exemption granted under paragraph 55(1)(c),

      • (ii) it was harvested in accordance with the requirements set out in subparagraph 52(c)(ii) or is the subject of an exemption granted under paragraph 55(1)(d),

      • (iii) it was harvested in accordance with the requirements set out in subparagraph 52(c)(iii) as it relates to soil or is the subject of an exemption granted under paragraph 55(1)(e),

      • (iv) it was harvested in accordance with the requirements set out in subparagraph 52(c)(iii) as it relates to surface and ground water resources or is the subject of an exemption granted under paragraph 55(1)(f),

      • (v) it was harvested in accordance with the requirements set out in subparagraph 52(c)(iii) as it relates to biodiversity or is the subject of an exemption granted under paragraph 55(1)(g), and

      • (vi) it was harvested in accordance with the requirements set out in subparagraph 52(c)(iv) or is the subject of an exemption granted under paragraph 55(1)(h);

    • (l) if the feedstock is a crop, a confirmation that it meets the requirements set out in section 50;

    • (m) the unique identifier for the declaration that they use for their internal accounting purposes;

    • (n) the date on which the declaration is made; and

    • (o) the signature of the person or their authorized agent.

  • Marginal note:Certification

    (2) If a feedstock referred to in paragraph 46(1)(c) is certified by a certification body in accordance with section 61, the declaration must be accompanied by a copy of the certificate and contain

    • (a) an indication of the requirements set out in sections 48 to 52 that the certified feedstock meets;

    • (b) the name of the certification scheme under which it was certified;

    • (c) the name of the certification body that certified the feedstock; and

    • (d) the day referred to in paragraph 70(2)(c) or (d) on which the certificate is expected to cease to be valid.

  • Marginal note:Declaration — foreign supplier

    (3) A declaration made by a foreign supplier must contain the following information:

    • (a) the name, civic address, postal address, telephone number and, if any, email address of the foreign supplier;

    • (b) if an authorized agent is making the declaration on behalf of the foreign supplier, the name, civic address, postal address, telephone number and, if any, email address of the authorized agent;

    • (c) the GPS coordinates to the fifth decimal place and, if any, civic address of the site where the mixing, processing or division, as the case may be, of the quantity of the feedstock was carried out or of the site where the quantity was obtained;

    • (d) the type of the feedstock that is used;

    • (e) the quantity of the feedstock that is used at the site referred to in paragraph (c) by the person mixing, processing, dividing or obtaining feedstock to produce low-carbon-intensity fuel, expressed in kilograms or cubic metres, as applicable;

    • (f) a confirmation that the requirements set out in subsection 47(2) were met with respect to any portion of the quantity of feedstock that was used to produce low-carbon-intensity fuel and that the foreign supplier has retained evidence of the compliance at the site where the low-carbon-intensity fuel was produced;

    • (g) a confirmation that the requirements set out in sections 48 to 52 are met with respect to the feedstock except if it is exempted under any of sections 53 to 55;

    • (h) the total quantity of low-carbon-intensity fuel that the foreign supplier produced outside Canada and that they sold for import into Canada;

    • (i) a confirmation that the foreign supplier is in compliance with subsection 59(1);

    • (j) in the case of a person who is the producer of the low-carbon-intensity fuel made using the feedstock, any alphanumeric identifier assigned to the fuel’s carbon intensity;

    • (k) the unique identifier for the declaration that the foreign supplier uses for their internal accounting purposes;

    • (l) the date on which the declaration is made; and

    • (m) the signature of the foreign supplier or their authorized agent.

  • Marginal note:Declaration by other person

    (4) A declaration made by a person referred to in any of subparagraphs 57(2)(a)(i) to (iv), other than a registered creator or foreign supplier, must contain the following information:

    • (a) the name, civic address, postal address, telephone number and, if any, email address of the person;

    • (b) if an authorized agent is making the declaration on behalf of the person, the name, civic address, postal address, telephone number and, if any, email address of the authorized agent;

    • (c) the GPS coordinates to the fifth decimal place and, if any, civic address of the site where the mixing, processing or division, as the case may be, of the quantity of the feedstock was carried out or of the site where the quantity was obtained;

    • (d) if the feedstock is sold, the name and civic and postal address of the person to whom it was sold;

    • (e) the type of the feedstock;

    • (f) the quantity of the feedstock that is removed from the site referred to in paragraph (c), expressed in kilograms or cubic metres, as applicable;

    • (g) a confirmation that, when the feedstock was removed from that site or was mixed, divided or obtained at that site, the requirements set out in subsection 47(1) were met with respect to the feedstock and that the person who mixed, divided or obtained the feedstock has retained evidence of compliance at that site;

    • (h) a confirmation that the requirements set out in sections 48 to 52 are met with respect to the feedstock except if it is exempted under any of sections 53 to 55;;

    • (i) in the case of a declaration referred to in subparagraph 57(2)(a)(iv) with respect to a quantity of a feedstock that is referred to in any of subparagraphs 46(1)(b)(ii) to (vi), a confirmation that the feedstock meets the requirements set out in section 50;

    • (j) in the case of a declaration referred to in subparagraph 57(2)(a)(iv), a confirmation that they have retained at the site referred to in paragraph (c), for each quantity of feedstock referred to in any of subparagraphs 46(1)(b)(iv) to (vi), delivery records, contracts and invoices that describe the location where that feedstock was first used;

    • (k) the unique identifier for the declaration that they use for their internal accounting purposes;

    • (l) the date on which the declaration is made; and

    • (m) the signature of the person or their authorized representative.

  • Marginal note:Unique identifier

    (5) The unique identifier referred to in paragraphs (1)(m), (3)(k) and (4)(k) must be unique to each declaration and indicate the lot number of the feedstock to which it applies. It must be used in all records related to material balances at the site to which it applies.

Marginal note:Producer records

  •  (1) A person who produces a quantity of low-carbon-intensity fuel using a feedstock referred to in paragraph 46(1)(b) or (c) must retain the following:

    • (a) delivery records, contracts and invoices with respect to each quantity of the feedstock that is brought to any of their facilities;

    • (b) the sales records for all low-carbon-intensity fuel, other than co-processed low-carbon-intensity fuel, that was produced using all or any portion of a quantity of the feedstock;

    • (c) records for all co-processed low-carbon-intensity fuel that demonstrate that it was produced using all or any portion of a quantity of eligible feedstock;

    • (d) a copy of the declaration made under paragraph 57(2)(a) by each person who possessed all or any portion of a quantity of the feedstock immediately before them;

    • (e) any information used to make the calculations referred to in subsections 45(1) and 47(2), the evidence that supports that information and the results of those calculations; and

    • (f) a copy of the certificate referred to in subsection 70(1), if any, that is issued with respect to the feedstock.

  • Marginal note:Importer records

    (2) A person who imports into Canada a quantity of low-carbon-intensity fuel must retain the following:

    • (a) delivery records, contracts and invoices with respect to the quantity of low-carbon-intensity fuel;

    • (b) the sales records for that quantity of low-carbon-intensity fuel; and

    • (c) if the low-carbon-intensity fuel is produced using an eligible feedstock referred to in paragraph 46(1)(b) or (c), a copy of the declaration made under subsection 58(3) by the foreign supplier of the fuel.

Marginal note:Non-application

 Sections 48, 49, 51 to 59 do not apply before January 1, 2024.

Marginal note:Certification

 An eligible feedstock referred to in paragraph 46(1)(c) may be certified only by a certification body that is eligible under section 63 and that conducts the certification in accordance with sections 64 to 74 and under a certification scheme that is approved by the Minister under section 62.

Marginal note:Approval by Minister

  •  (1) The Minister may approve a certification scheme if the following conditions are met:

    • (a) the Minister is satisfied that the applicable requirements set out in sections 48 to 52 will be met in respect of all of the feedstock certified using the certification scheme’s procedures;

    • (b) the certification scheme is developed and maintained by a person who is the scheme owner and that person

      • (i) has structures in place for operating and managing the certification scheme,

      • (ii) creates, maintains and has control of adequate documentation for the operation, maintenance and improvement of the certification scheme,

      • (iii) has measures in place to respond to complaints with respect to the certification scheme,

      • (iv) has measures in place to retain records securely for 10 years,

      • (v) creates, maintains and has control of an information management system,

      • (vi) protects the confidentiality of information provided by the parties involved in the certification scheme, and

      • (vii) has developed requirements that comply with sections 63 to 67 for certification bodies, as well as requirements regarding the specific competencies required of certification bodies and the way in which certification bodies are to demonstrate their compliance with those requirements;

    • (c) in the case where the feedstock is harvested in accordance with a forest management plan referred to in section 52, the certification scheme provides that the management plan must be assessed by a specialist in forestry;

    • (d) a plan is in place to review the certification scheme at planned intervals;

    • (e) procedures are in place to review the certification scheme when

      • (i) there is a significant change to the certification scheme, or

      • (ii) a complaint is received that indicates that a review is necessary;

    • (f) procedures, including for considering comments from stakeholders, are in place to ensure that the integrity, exhaustiveness and effectiveness of the certification scheme is verified during reviews;

    • (g) the certification scheme includes procedures to ensure that the following are publicly available:

      • (i) the most recent versions of the certification scheme and documentation for the scheme that are in the common language of each region to which the certification scheme applies,

      • (ii) a list, current to the day, of the feedstock harvesters that are certified under the certification scheme,

      • (iii) a list of certification bodies that are authorized to conduct audits under the certification scheme,

      • (iv) a list of certification bodies that were previously authorized to conduct audits under the certification scheme, including an indication as to whether those bodies are no longer authorized on a permanent or temporary basis, and

      • (v) contact information for the scheme owner;

    • (h) the certification scheme provides that a list of persons who have not complied with the certification scheme must be submitted, on request, to the Minister;

    • (i) in the case of a certification scheme that permits a group of producers to be certified together, the certification scheme requires that

      • (i) the producers in the group use similar production systems and information management systems and harvest feedstock of the same type and in areas that are near each other and have similar climatic conditions, and

      • (ii) there be clear conditions and procedures for a producer to join the group;

    • (j) the certification scheme sets out the measures that a certification body must take if a feedstock producer fails to comply with the certification scheme, including

      • (i) the denial of an application for certification or the revocation of a certificate in accordance with section 71, or the denial of an application for certification or the suspension of a certificate in accordance with section 72, in the circumstances indicated by the certification scheme, and

      • (ii) the establishment of procedures in respect of corrective actions that must be taken with respect to the circumstances of non-conformity referred to in section 73;

    • (k) the certification scheme includes conditions on the ways in which a feedstock harvester may use certificates issued under it; and

    • (l) the certification scheme owner monitors the use of certificates issued under the certification scheme.

  • Marginal note:End of approval

    (2) A certification scheme ceases to be approved on the earlier of

    • (a) sixty days after the day on which there is a change to the scope of the scheme, unless the scheme owner notifies the Minister of the change and the Minister determines that, despite the change, the scheme continues to meet the conditions for approval,

    • (b) sixty days after the day on which there is a change to any procedure set out in the scheme on which the Minister’s approval was based, unless the scheme owner notifies the Minister of the change and the Minister determines that, despite the change, the scheme continues to meet the conditions for approval,

    • (c) the first anniversary of the day on which the scheme was most recently approved by the Minister unless, before that anniversary, the scheme owner submits a report that contains the information referred to in Schedule 5 to the Minister concerning the operation of the certification scheme during the preceding year,

    • (d) the first anniversary of the day on which the scheme owner most recently submitted a report that contains the information referred to in Schedule 5 to the Minister concerning the operation of the certification scheme within the preceding year, and

    • (e) the fifth anniversary of the day on which the scheme was most recently approved by the Minister.

Marginal note:Eligibility conditions for accreditation

  •  (1) A person is eligible to be accredited as a certification body by the Standards Council of Canada, the American National Standards Institute (ANSI) National Accreditation Board or a designated accreditation body if the person

    • (a) meets the applicable requirements set out in ISO/IEC Standard 17065 or, in the case of a certification body that assesses a forest management plan referred to in section 52, meets the applicable requirements set out in ISO/IEC Standard 17021-1; and

    • (b) demonstrates that they comply with the competency requirements of the certification scheme for which they are to be accredited.

  • Marginal note:Designation of accreditation body

    (2) The Minister may designate an accreditation body as a designated accreditation body if it is a member of the International Accreditation Forum or an equivalent body and meets the requirements set out in ISO/IEC Standard 17011.

  • Marginal note:Suspended or revoked accreditation

    (3) The certification of a feedstock must not be conducted by a certification body whose accreditation is suspended or revoked.

Marginal note:No outsourcing

 It is not permitted to outsource any of the activities that are carried out as part of the certification of a feedstock.

Marginal note:Consecutive certifications

 The certification of a feedstock must be conducted by a team that does not include any individual who has contributed to the certification of the feedstock for five consecutive compliance periods, unless three compliance periods have elapsed since the most recent of those consecutive compliance periods.

Marginal note:Certification team — members

  •  (1) A certification team must consist only of members who meet the requirements of clause 7 of ISO Standard 19011 and must include the following individuals:

    • (a) a team leader who is competent with respect to the feedstock being certified;

    • (b) if it is relevant to the feedstock being certified, at least one specialist in forestry or agriculture, as the case may be, who is recognized as a forestry engineer, professional forester, agricultural engineer or agrologist by

      • (i) a Canadian professional association, in the case of forestry or agriculture that occurs in Canada, and

      • (ii) a relevant national authority of the country in which the forestry or agriculture occurs, in any other case; and

    • (c) if it is relevant to the feedstock being certified, at least one specialist in biodiversity who holds a bachelor’s degree in biology, natural sciences or environmental sciences granted by a Canadian university, or an equivalent degree granted by a university outside Canada.

  • Marginal note:Person responsible for making decision

    (2) The person responsible for making a certification decision must have, at a minimum, the same competencies as those set out for an audit team leader in subclause 7.2.3.4 of ISO Standard 19011.

Marginal note:Applicable standards for certification

  •  (1) A certification body must conduct a certification in accordance with the Methods for Verification and Certification and with

    • (a) ISO/IEC Standard 17065 or, in the case where the feedstock is harvested in accordance with a forest management plan referred to in section 52, ISO/IEC Standard 17021-1; and

    • (b) ISO Standard 19011.

  • Marginal note:Interpretation of ISO/IEC Standard 17065

    (2) For the purposes of ISO/IEC Standard 17065

    • (a) a reference to a “product requirement” in subclause 3.8 of that Standard is to be read as a reference to the requirements set out in sections 48 to 52 of these Regulations; and

    • (b) a reference to a “location” in that Standard is to be read as a reference to a farm, forest or any other place where the feedstock is harvested.

  • Marginal note:Interpretation of ISO/IEC Standard 17021-1

    (3) For the purposes of ISO/IEC Standard 17021-1,

    • (a) a reference to an “audit criteria” in subclause 9.2.1 of that Standard is to be read as a reference to the requirements set out in section 52 of these Regulations; and

    • (b) a reference to a “site” in that Standard is to be read as a reference to a farm, forest or any other place where the feedstock is harvested.

Marginal note:Annual surveillance audit

 The certification of a feedstock conducted by a certification body must include an annual surveillance audit to ensure that the feedstock is harvested in accordance with the requirements of sections 48 to 52.

Marginal note:Site visits

  •  (1) The certification of a feedstock conducted by a certification body must include a site visit if it is the first certification of the feedstock or if, in the case of any subsequent audit, the risk of any non-conformity with the certification scheme is high.

  • Marginal note:Remote audits

    (2) A site visit is not required during the conduct of a surveillance audit if

    • (a) the collection of data may be done remotely in a manner that reduces, to a reasonable level, the risk of failing to detect any non-conformity with the certification scheme; or

    • (b) the risk of any non-conformity with the certification scheme is low.

Marginal note:Unambiguous identification

  •  (1) A certificate issued by a certification body must unambiguously identify the feedstock to which it applies.

  • Marginal note:End of certification

    (2) The certificate ceases to be valid on the earlier of

    • (a) the day on which a certification body, on the basis of an audit it conducted, is no longer satisfied that the applicable requirements set out in sections 48 to 52 are met,

    • (b) the day that is the first anniversary of the day on which the most recent audit was conducted by the certification body,

    • (c) the day that is the fifth anniversary of the day on which the certificate was issued, and

    • (d) the day specified by the certification scheme under which the certification body conducts the certification.

Marginal note:Denial or revocation

  •  (1) If any of the following circumstances occur with respect to a feedstock, an application for the certification of the feedstock must be denied or, in the case where a certificate has been issued for the feedstock, the certificate must be revoked:

    • (a) the applicable requirements set out in sections 48 to 52 are not met with respect to the feedstock and the situation cannot be rectified by corrective action;

    • (b) the producer of the feedstock fails to comply with the certification scheme and the situation cannot be rectified by taking corrective action;

    • (c) the producer of the feedstock fails to comply with the certification scheme in a manner that undermines the integrity of the certification scheme.

  • Marginal note:New application for certification

    (2) The producer of a feedstock in respect of which an application for certification has been denied, or a certificate has been revoked, under subsection (1) may submit a new application for certification of the feedstock after the end of the period specified by the certification scheme.

Marginal note:Denial or suspension of certification

  •  (1) If any of the following circumstances occur with respect to a feedstock, an application for the certification of the feedstock must be denied or, in the case where a certificate has been issued for the feedstock, the certificate must be suspended:

    • (a) the applicable requirements set out in sections 48 to 52 are not met with respect to the feedstock and the situation can be rectified by taking corrective action;

    • (b) the producer of the feedstock repeatedly fails to comply with the certification scheme, including in the following cases:

      • (i) more than 5% of the evidence that is provided to the certification body and included in a representative sample contains gaps or errors,

      • (ii) the producer fails to disclose their participation in other certification schemes during the certification process, or

      • (iii) the producer fails to provide the certification body with any relevant information.

  • Marginal note:Duration of suspension

    (2) The suspension of the certificate begins on the day on which the producer of the feedstock is notified of the suspension and ends after 90 days.

  • Marginal note:Revocation

    (3) The certificate must be revoked at the end of the 90‑day suspension period if the producer of the feedstock has not taken corrective action with respect to the situation that resulted in the suspension.

Marginal note:Other circumstances of non-conformity

  •  (1) A certification scheme may, if a producer of a feedstock has not complied with the scheme in circumstances other than those referred to in subsections 71(1) and 72(1), provide for a period during which the producer must take corrective action with respect to the circumstances of non-conformity.

  • Marginal note:Time limit for corrective action

    (2) The period within which the producer must take the corrective action ends on the earlier of

    • (a) the day on which the next surveillance audit of the feedstock is to be conducted, 

    • (b) the day on which the certification is renewed,

    • (c) the day that is 12 months after the day on which the producer of the feedstock is notified of the non-conformity by the certification body, and

    • (d) the day specified by the certification scheme.

Marginal note:Prior certification under another certification scheme

 An application for the certification of a feedstock must contain the following information:

  • (a) a statement as to whether the feedstock has, in the previous five years, been the subject of a certification under another certification scheme;

  • (b) all relevant information relating to a certification of the feedstock under another certification scheme, including audit reports and any decisions to suspend or revoke the certification during the previous five years, as well as the reasons for any suspension or revocation; and

  • (c) a statement specifying the reasons for which any producer of the feedstock withdrew from another certification scheme before the first surveillance audit.

Determination of Carbon Intensity

Marginal note:Low-carbon-intensity fuel

  •  (1) The carbon intensity of a low-carbon-intensity fuel, other than hydrogen produced from a fossil fuel, and the carbon intensity of a material input that is a renewable natural gas, biogas, renewable propane or hydrogen, other than hydrogen produced from a fossil fuel, is, at the election of the registered creator or foreign supplier,

    • (a) the default carbon intensity referred to in section 1 of Schedule 6; or

    • (b) determined by the formula

      CIf + CIp + CIcl + CIe + CItd + CIc

      where

      CIf
      is the quantity of CO2e emissions set out in section 2 of Schedule 6 that represents the quantity of CO2e that is associated with the extraction or production, as the case may be, of the feedstock from which the fuel or material input is produced, per megajoule of energy produced,
      CIp
      is the quantity of CO2e emissions set out in section 3 of Schedule 6 that represents the quantity of CO2e that is released during the production of the fuel or material input from the feedstock, the transportation of the feedstock and intermediary products used to produce the fuel or material input and the distribution of the fuel or material input to end users, per megajoule of energy produced,
      CIcl
      is the quantity of CO2e emissions set out in section 4 of Schedule 6 that represents the quantity of CO2e that is released during the compression or liquefaction of the fuel or material input, per megajoule of energy produced,
      CIe
      is the quantity of CO2e emissions set out in section 5 of Schedule 6 that represents the additional quantity of CO2e that is associated with the production of electricity used during the production of the fuel or material input, per megajoule of energy produced,
      CItd
      is the quantity of CO2e emissions set out in section 6 of Schedule 6 that represents the additional quantity of CO2e that is released during the transportation of the feedstock and intermediary products used to produce the fuel or material input and the distribution of the fuel or material input to end users, per megajoule of energy produced, in the case of a total transportation distance of no less than 1500 km, and
      CIc
      is the quantity of CO2e emissions set out in section 7 of Schedule 6 that represents the quantity of CO2e that is released during the combustion of the fuel or the use of the material input, per megajoule of energy produced.
  • Marginal note:Use limited to 12 months

    (2) The default carbon intensity referred to in paragraph (1)(a) must not be used to create compliance credits for a period of more than 12 consecutive months or more than 12 months during two consecutive compliance periods, unless the Minister, at the written request of the registered creator, approves the use of that carbon intensity for any longer period specified by the Minister.

  • Marginal note:Use pending approval

    (3) However, in the case of an application under subsection 80(1) for the approval of a carbon intensity determined in accordance with paragraph (1)(b) or subsection 76(1), the applicant may use the default carbon intensity referred to in paragraph (1)(a) to create compliance credits during the period beginning on the day on which the application is made and ending on the day on which the carbon intensity is approved under subsection 85(1), even if that period is longer than 12 consecutive months.

  • Marginal note:Input data for less than three months

    (4) A registered creator or foreign supplier may elect to use the carbon intensity referred to in paragraph (1)(b) if they have input data, for a period of less than three consecutive months, derived from the activities referred to in the definition carbon intensity in subsection 1(1) that are carried out over the life cycle of the fuel or the life cycle of the material input, as the case may be.

  • Marginal note:Use limited to three compliance periods

    (5) The carbon intensity referred to in paragraph (1)(b) must not be used to create credits other than for a period of no more than three consecutive compliance periods.

  • Marginal note:Fossil fuels

    (6) For the purposes of subsections 98(2), 99(3) and (4) and 104(2), the carbon intensity of a fuel that is hydrogen, propane, natural gas, liquefied natural gas and compressed natural gas is, at the election of the registered creator, the amount set out in

    • (a) section 8 of Schedule 6; or

    • (b) the Specifications for Fuel LCA Model CI Calculations.

  • Marginal note:Electricity

    (7) The carbon intensity of electricity for a province in which a charging station is located is, at the election of the registered creator, the amount set out for that province in

    • (a) section 9 of Schedule 6; or

    • (b) the Specifications for Fuel LCA Model CI Calculations.

Marginal note:Fuel LCA Model — registered creator or foreign supplier

  •  (1) A registered creator or foreign supplier may elect to determine the carbon intensity of a low-carbon-intensity fuel, or the carbon intensity of a material input that is a renewable natural gas, biogas, renewable propane or hydrogen, using the Fuel LCA Model in accordance with the option set out in either paragraph (3)(a) or (b), if they have input data, for a period of 24 consecutive months during the period of 30 months that immediately precedes the day on which they make the election, derived from the activities referred to in the definition carbon intensity in subsection 1(1) that are carried out over the life cycle of the fuel or material input, as the case may be.

  • Marginal note:Carbon-intensity contributor

    (2) A carbon-intensity contributor may elect to determine the carbon intensity of a low-carbon-intensity fuel or material input that is a renewable natural gas, biogas, renewable propane or hydrogen in accordance with the option set out in either paragraph (3)(a) or (b), if they have input data, for a period of 24 consecutive months during the period of 30 months that immediately precedes the day on which they make the election, derived from the activities referred to in the definition carbon intensity in subsection 1(1) that are carried out over the life cycle of the fuel or material input, as the case may be.

  • Marginal note:Options on election

    (3) The carbon intensity may be determined based on the input data referred to in subsection (1) or (2) in accordance with either of the following options:

    • (a) an existing pathway from the Fuel LCA Model; or

    • (b) a new pathway created by the registered creator, carbon-intensity contributor or foreign supplier from the Fuel LCA Model, in the case where

      • (i) the fuel or material input is not indicated in the Fuel LCA Model,

      • (ii) the feedstock used to produce the fuel or material input is not indicated in the Fuel LCA Model, or

      • (iii) the criteria provided in the Specifications for Fuel LCA Model CI Calculations for creating a new pathway are met.

Marginal note:Fuel LCA Model — co-processed low-carbon-intensity fuel

 A registered creator or foreign supplier must determine the carbon intensity of a co-processed low-carbon-intensity fuel using the Fuel LCA Model in accordance with the applicable specific emission-reduction quantification method established under subsection 32(1) and either of the following options:

  • (a) an existing pathway from the Fuel LCA Model; or

  • (b) a new pathway created by the registered creator or foreign supplier from the Fuel LCA Model, in the case where

    • (i) the fuel is not indicated in the Fuel LCA Model,

    • (ii) the feedstock used to produce the fuel is not indicated in the Fuel LCA Model, or

    • (iii) the criteria provided in the Specifications for Fuel LCA Model CI Calculations for creating a new pathway are met.

Marginal note:Compressed and liquefied gases

  •  (1) Instead of determining the carbon intensity of propane, liquefied natural gas or compressed natural gas in accordance with subsection 75(6), a registered creator may elect to make that determination using the Fuel LCA Model in accordance with the option set out in either paragraph (3)(a) or (b), if they have input data, for a period of 24 consecutive months during the period of 30 months that immediately precedes the day on which they make the election, respecting the operation of a fuelling station or the liquefaction process for propane, renewable propane, co-processed low-carbon intensity propane, compressed natural gas, renewable compressed natural gas, liquefied natural gas or renewable liquefied natural gas.

  • Marginal note:Renewable fuels

    (2) In the case of renewable propane, co-processed low-carbon-intensity propane, renewable compressed natural gas and renewable liquefied natural gas, the determination is to be made as if

    • (a) the renewable propane or co-processed low-carbon-intensity propane were propane;

    • (b) the renewable compressed natural gas were compressed natural gas; or

    • (c) the liquefied renewable natural gas were liquefied natural gas.

  • Marginal note:Options on election

    (3) The carbon intensity may be determined based on the input data referred to in subsection (1) in accordance with either of the following options:

    • (a) an existing pathway from the Fuel LCA Model; or

    • (b) a new pathway created by the registered creator or foreign supplier from the Fuel LCA Model, in the case where

      • (i) the fuel is not indicated in the Fuel LCA Model,

      • (ii) the feedstock used to produce the fuel is not indicated in the Fuel LCA Model, or

      • (iii) the criteria provided in the Specifications for Fuel LCA Model CI Calculations for creating a new pathway are met.

Marginal note:Electricity

  •  (1) A registered creator or carbon-intensity contributor may elect to determine, in accordance with subsection (3), the carbon intensity of the electricity supplied to electric vehicles by a charging station that is not intended primarily for use by the occupants of a private dwelling-place if they have input data respecting the source and quantity of that electricity for a period of 24 consecutive months during the period of 30 months that immediately precedes the day on which they make the election.

  • Marginal note:Electricity — fuelling station or facility

    (2) A registered creator or carbon-intensity contributor may elect to determine, in accordance with subsection (3), the carbon intensity of the electricity supplied to a fuelling station or facility if they have input data respecting the source and quantity of that electricity for a period of 24 consecutive months during the period of 30 months that immediately precedes the day on which they make the election.

  • Marginal note:Options on election

    (3) The carbon intensity may be determined based on the input data referred to in subsection (1) or (2) in accordance with either of the following options:

    • (a) an existing pathway from the Fuel LCA Model; or

    • (b) a new pathway created by the registered creator or carbon-intensity contributor from the Fuel LCA Model, in the case where the source of the electricity is not indicated in the Fuel LCA Model or where the criteria indicated in the Specifications for Fuel LCA Model CI Calculations for creating a new pathway are met.

Marginal note:Application for approval of carbon intensity

  •  (1) A registered creator, carbon-intensity contributor or foreign supplier may apply to the Minister for the approval of a carbon intensity determined in accordance with paragraph 75(1)(b) or any of sections 76 to 79, as the case may be.

  • Marginal note:Carbon-intensity additional value

    (2) In the case of an application for the approval of a carbon intensity determined in accordance with section 76, 78 or 79, the registered creator, carbon-intensity contributor or foreign supplier may add an additional value to that carbon intensity, in which case the carbon intensity that is the subject of the application for approval would be the sum of the additional value and the carbon intensity determined using the Fuel LCA Model.

  • Marginal note:Imported fuel

    (3) Despite subsection (1), in the case of a fuel produced outside Canada and imported into Canada in respect of which compliance credits are created under paragraph 19(1)(b) or 20(b) or when a CO2e-emission-reduction project described in paragraph 30(d) is carried out, only the foreign supplier of the fuel may make the application for the approval of the carbon intensity.

  • Marginal note:Distinct application — each feedstock

    (4) A distinct application for the approval of a carbon intensity is required for each type of feedstock that is used to produce a low-carbon-intensity fuel or a material input that is renewable natural gas, biogas, renewable propane or hydrogen, including in the case where two or more types of feedstock are used simultaneously to produce the low-carbon-intensity fuel or the material input.

Marginal note:Pathway approval

  •  (1) Before making an application under subsection 80(1) for the approval of a carbon intensity based on a new pathway referred to in paragraph 76(3)(b), 77(b), 78(3)(b) or 79(3)(b), the registered creator, carbon-intensity contributor or foreign supplier must apply to the Minister for the approval of the new pathway.

  • Marginal note:Application

    (2) The application for the approval of a new pathway must include the information referred to in Schedule 7.

  • Marginal note:Approval

    (3) The Minister must approve the new pathway if the Minister is satisfied that the pathway is based on

    • (a) a plan to collect verifiable data and results;

    • (b) calculations that do not contain any error that attains any of the quantitative materiality thresholds referred to in paragraph 150(a);

    • (c) unit processes, modelling parameters, background data sets and a methodology that are appropriate for the pathway; and

    • (d) a methodology that is consistent with ISO Standard 14040, ISO Standard 14044 and the Specifications for Fuel LCA Model CI Calculations.

  • Marginal note:Unique alphanumeric identifier

    (4) When the Minister approves the new pathway, the Minister must assign a unique alphanumeric identifier to it.

Marginal note:Information to be provided

  •  (1) An application made under section 80 in respect of a carbon intensity determined in accordance with paragraph 75(1)(b) or section 76 or 77 must contain the information referred to in section 1 of Schedule 8.

  • Marginal note:Additional information — paragraph 75(1)(b)

    (2) In the case of a carbon intensity determined in accordance with paragraph 75(1)(b), the application must also contain the information referred to in section 2 of Schedule 8.

  • Marginal note:Additional information — section 76

    (3) In the case of a carbon intensity determined in accordance with section 76, the application must also contain the information referred to in sections 3 and 6 of Schedule 8, as well as any information specified in any applicable emission-reduction quantification method established under subsection 31(1) or 32(1).

  • Marginal note:Additional information — section 77

    (4) In the case of a carbon intensity determined in accordance with section 77, the application must also contain the information referred to in sections 3 and 6 of Schedule 8, as well as any information specified in any applicable specific emission-reduction quantification method established under subsection 32(1).

Marginal note:Information to be provided — section 78

 In the case of a carbon intensity determined in accordance with section 78, an application made under section 80 must contain the information referred to in sections 4 and 6 of Schedule 8.

Marginal note:Information to be provided — section 79

 In the case of a carbon intensity determined in accordance with section 79, an application made under section 80 must contain the information referred to in sections 5 and 6 of Schedule 8.

Marginal note:Approval

  •  (1) The Minister must approve a carbon intensity for which an application for approval is made under section 80 if the Minister is satisfied that the determination of the carbon intensity is based on

    • (a) data and results that are verifiable;

    • (b) calculations that do not contain any error that attains any of the quantitative materiality thresholds referred to in paragraph 150(a);

    • (c) unit processes, modelling parameters, background data sets and a methodology that are appropriate for that determination and do not result in an underestimation of the carbon intensity;

    • (d) in the case of a determination made in accordance with section 76 or 77, a methodology that is consistent with ISO Standard 14040, ISO Standard 14044 and the Specifications for Fuel LCA Model CI Calculations; and

    • (e) with respect to an application referred to in section 130, an unqualified opinion issued in accordance with paragraph 154(a) or a qualified opinion issued in accordance with paragraph 154(b).

  • Marginal note:Unique alphanumeric identifier

    (2) When the Minister approves the carbon intensity, the Minister must assign it a unique alphanumeric identifier.

Marginal note:End of validity

  •  (1) The approved carbon intensity of a low-carbon-intensity fuel or material input ceases to be valid if a change is made to the extraction or production processes for the feedstock used to produce the fuel or material input or the production processes and that change is not consistent with the emission factors, input data, background data sets and methodology that were used to determine the carbon intensity and would result in,

    • (a) in the case where the carbon intensity was determined in accordance with paragraph 75(1)(b), production processes that are different than those used to determine the approved carbon intensity of the fuel or material input;

    • (b) in the case where the carbon intensity was determined in accordance with section 76, an actual carbon intensity of the fuel or material input — as specified in the carbon-intensity-pathway report referred to in subsection 123(1) — that is greater than the approved carbon intensity by at least

      • (i) 1 gCO2e/MJ, if the absolute value of the approved carbon intensity is less than 20 gCO2e/MJ,

      • (ii) 5%, if the absolute value of the approved carbon intensity is between 20 and 100 gCO2e/MJ, and

      • (iii) 5 gCO2e/MJ, if the absolute value of the approved carbon intensity is greater than 100 gCO2e/MJ; and

    • (c) in the case where the carbon intensity was approved for a CO2e-emission-reduction project described in paragraph 30(d), fuel production processes or conditions that are different than those indicated in the application made under subsection 80(1) for the approval of the carbon intensity.

  • Marginal note:Non-compliance with section 123

    (2) The approved carbon intensity of a fuel or material input ceases to be valid if the registered creator, carbon-intensity contributor or foreign supplier who made the application for approval under subsection 80(1) fails to comply with the requirements set out in section 123.

  • Marginal note:Non-compliance with section 124

    (3) The approved carbon intensity of a gaseous or liquid low-carbon-intensity fuel that was produced using a quantity of an eligible feedstock referred to in paragraph 46(1)(b) or (c) ceases to be valid if the registered creator or foreign supplier who made the application for approval under subsection 80(1) fails to comply with the requirements set out in section 124.

  • Marginal note:Non-compliance with specific quantification method

    (4) The approved carbon intensity of a co-processed low-carbon-intensity fuel ceases to be valid if a registered creator or foreign supplier referred to in subsection 80(1) fails to comply with the applicable specific emission-reduction quantification method established under subsection 32(1).

  • Marginal note:Non-compliance with record requirements

    (5) The approved carbon intensity of a low-carbon-intensity fuel or material input may be invalidated by the Minister if the registered creator, carbon-intensity contributor or foreign supplier who made the application for approval under subsection 80(1) fails to comply with any of the requirements set out in sections 166 and 168 in relation to the approved carbon intensity.

  • Marginal note:End of validity — certain gases

    (6) The approved carbon intensity of propane, liquefied natural gas or compressed natural gas determined in accordance with section 78 ceases to be valid if a change is made to the compression or liquefaction process for the fuel and that change is not consistent with the emission factors, input data, background data sets and methodology that were used to determine the carbon intensity and would result in an actual carbon intensity of the fuel — as specified in the carbon-intensity-pathway report referred to in subsection 123(1) — that is greater than the approved carbon intensity by at least

    • (a) 1 gCO2e/MJ, if the absolute value of the approved carbon intensity is less than 20 gCO2e/MJ;

    • (b) 5%, if the absolute value of the approved carbon intensity is between 20 and 100 gCO2e/MJ; and

    • (c) 5 gCO2e/MJ, if the absolute value of the approved carbon intensity is greater than 100 gCO2e/MJ.

  • Marginal note:End of validity — electricity

    (7) The approved carbon intensity of electricity determined in accordance with section 79 ceases to be valid if a change is made to the source and quantity of electricity supplied to electric vehicles or facilities and that change would result in an actual carbon intensity of the electricity — as specified in the carbon-intensity-pathway report referred to in subsection 123(1) — that is greater than the approved carbon intensity by at least

    • (a) 1 gCO2e/MJ, if the absolute value of the approved carbon intensity is less than 20 gCO2e/MJ;

    • (b) 5%, if the absolute value of the approved carbon intensity is between 20 and 100 gCO2e/MJ; and

    • (c) 5 gCO2e/MJ, if the absolute value of the approved carbon intensity is greater than 100 gCO2e/MJ.

  • Marginal note:Transferred carbon intensity

    (8) The approved carbon intensity of a fuel or material input ceases to be valid if the registered creator, carbon-intensity contributor or foreign supplier who made the application for the approval of that carbon intensity under subsection 80(1) has determined it by using a carbon intensity that ceases to be valid under any of subsections (1) to (7).

  • Marginal note:End of validity — December 31, 2025

    (9) A carbon intensity determined in accordance with any of sections 76 to 79 that was approved by the Minister before July 1, 2024 ceases to be valid on December 31, 2025. The registered creator, carbon-intensity contributor or foreign supplier may, on or after July 1, 2024, submit a new application to the Minister for the approval of the carbon intensity under subsection 80(1).

Marginal note:New application

  •  (1) A registered creator or foreign supplier may apply to replace a carbon intensity approved by the Minister under subsection 85(1) with the actual carbon intensity determined in accordance with section 76, 78 or 79, in the case where the actual carbon intensity — as specified in the carbon-intensity-pathway report referred to in subsection 123(1) — is lower than the approved carbon intensity and the difference between the two intensities is at least

    • (a) 1 gCO2e/MJ, if the absolute value of the approved carbon intensity is less than 20 gCO2e/MJ;

    • (b) 5%, if the absolute value of the approved carbon intensity is between 20 and 100 gCO2e/MJ; and

    • (c) 5 gCO2e/MJ, if the absolute value of the approved carbon intensity is greater than 100 gCO2e/MJ.

  • Marginal note:New application — carbon-intensity contributor

    (2) A carbon-intensity contributor may apply to replace a carbon intensity that has been approved by the Minister under subsection 85(1) with the actual carbon intensity determined in accordance with section 76 or 79 in the case where the actual carbon intensity — as specified in the carbon-intensity-pathway report referred to in subsection 123(1) — is lower than the approved carbon intensity and the difference between the two intensities is at least

    • (a) 1 gCO2e/MJ, if the absolute value of the approved carbon intensity is less than 20 gCO2e/MJ;

    • (b) 5%, if the absolute value of the approved carbon intensity is between 20 and 100 gCO2e/MJ; and

    • (c) 5 gCO2e/MJ, if the absolute value of the approved carbon intensity is greater than 100 gCO2e/MJ.

Marginal note:Adjustment of credits

  •  (1) A registered creator may — in the first annual credit-creation report that they submit under section 120 or first credit-adjustment report that they submit under section 122 following the approval under subsection 85(1) of the carbon intensity of a fuel or energy source determined in accordance with section 76, 78 or 79 — request that compliance credits be created for the three compliance periods preceding the approval of the carbon intensity if

    • (a) the carbon intensity indicated in that credit-creation report or that credit-adjustment report was determined in accordance with section 75 or was temporarily approved under subsection 91(4);

    • (b) the fuel for which the carbon intensity was approved under subsection 85(1) is produced from the same type of feedstock and in the same production process as the fuel or electricity used during the preceding compliance periods for which a credit adjustment is requested; and

    • (c) the carbon intensity that was approved under subsection 85(1) was determined in accordance with section 76, 78 or 79 after July 1, 2024.

  • Marginal note:Number of adjusted compliance credits

    (2) The number of compliance credits that may be created by a registered creator under subsection (1) is equal to the difference between

    • (a) the maximum number of compliance credits that would be created for the three compliance periods preceding the approval of the carbon intensity using the information contained in the report that they submit under section 120 or 122 in respect of those compliance periods and using the carbon intensity that was determined in accordance with section 76, 78 or 79, as the case may be, and

    • (b) the total number of compliance credits that were created by the registered creator for the three compliance periods preceding the approval of the carbon intensity using the carbon intensity that was determined in accordance with section 75 or that was temporarily approved under subsection 91(4), as the case may be.

Loading…