551.01 [Repealed, SOR/2009-280, s. 27]
Canadian Aviation Regulations
SOR/96-433In forceCurrent to September 30, 2026 (Justice Canada: October 19)16 amendments not yet in forceHistoryRegistered on September 10, 1996Made under: Aeronautics Act
Part V — Airworthiness › Subpart 51 — [Repealed, SOR/2009-280, s. 27]
Subpart 61 — Manufacture of Aeronautical Products
Interpretation
561.01 In this Subpart,
- design approval
design approval means a type certificate, a supplemental type certificate, a part design approval, a Canadian Technical Standard Order (CAN-TSO) design approval or a document equivalent to any of those documents that is issued by the airworthiness authority of a foreign state; (approbation de conception)
- manual
manual means the manual established under section 561.07; (manuel)
- Standard 561
Standard 561 means Standard 561 — Standard for Approved Manufacturers. (norme 561)
- SOR/2005-348, s. 4
- SOR/2009-280, s. 28
Application
561.02 This Subpart applies in respect of the manufacture of an aeronautical product in respect of which a design approval has been issued but does not apply in respect of
(a) maintenance;
(b) the manufacture of standard parts;
(c) the manufacture of commercial parts; or
(d) the manufacture of parts during a repair or modification under subsection 571.06(4).
- SOR/2005-348, s. 4
Manufacturer Certificate — Application, Issuance and Amendment
561.03 (1) An applicant for the issuance or amendment of a manufacturer certificate respecting an aeronautical product shall submit an application to the Minister that includes the documents specified in section 561.03 of Standard 561.
(2) An applicant for the issuance or amendment of a manufacturer certificate respecting an aeronautical product shall
(3) An applicant for the issuance or amendment of a manufacturer certificate respecting an aeronautical product shall demonstrate that they have access to all present and future design data, process specifications and other related information necessary for the continuing airworthiness of the aeronautical product.
(4) The Minister shall issue or amend a manufacturer certificate authorizing an applicant to manufacture the aeronautical products set out in the manufacturer certificate if the applicant meets the requirements of this Subpart.
(5) A manufacturer certificate may authorize the manufacture of a limited number of an aeronautical product where
(6) Unless an expiry date is specified in the manufacturer certificate issued under subsection (4), the certificate shall remain in effect until it is surrendered by the manufacturer or suspended or cancelled.
(7) A manufacturer certificate is not transferable.
(8) Except as provided in section 561.06, the final assembly facilities for an aeronautical product specified in a manufacturer certificate shall be located in Canada.
- SOR/2005-348, s. 4
Management Personnel
(2) [Repealed, SOR/2022-246, s. 12]
(3) [Repealed, SOR/2022-246, s. 12]
(4) [Repealed, SOR/2022-246, s. 12]
(5) The holder of a manufacturer certificate shall provide the person appointed with the authority and the financial and human resources necessary to ensure that the requirements of this Subpart are met.
(6) The person appointed may assign responsibility for the management of specific activities, systems or programs required by this Subpart to other persons, provided that the assignments and the scope of the assigned responsibilities are specified in the manual.
(7) The holder of a manufacturer certificate shall ensure that no person is appointed under paragraph (1)(a) or remains responsible for the activities referred to in that paragraph if, at the time of their appointment or during their tenure, they have a record of conviction for
- SOR/2005-348, s. 4
- SOR/2019-119, s. 27(F)
- SOR/2022-246, s. 12
Resources
561.05 The holder of a manufacturer certificate shall have, and ensure that any supplier referred to in section 561.13 has, the financial and human resources necessary for the manufacture and inspection of any aeronautical product specified in the manufacturer certificate, including those specified in section 561.05 of Standard 561.
- SOR/2005-348, s. 4
Facilities Located in a Foreign State
561.06 If an arrangement exists between Canada and a foreign state concerning the manufacture of an aeronautical product, the holder of a manufacturer certificate may be authorized to perform their activities under the certificate in facilities located in that foreign state if the holder
(a) submits a written application to that effect to the Minister;
(b) gives, by a written agreement, an undertaking to the Minister to ensure that the Minister has access to those facilities to verify that the performance of the activities complies with the requirements of the Act and these Regulations, as if those facilities were located in Canada; and
(c) undertakes to pay the expenses referred to in paragraphs 104.04(1)(a) and (b) incurred by the Department of Transport under paragraph (b).
- SOR/2005-348, s. 4
Manual
561.07 (1) The holder of a manufacturer certificate shall establish, maintain and require the use of a manual that must include the information set out in section 561.07 of Standard 561 and that sets out policies and procedures respecting the construction and inspection of the aeronautical products specified in the manufacturer certificate.
(2) Subject to subsection (4), the person appointed under paragraph 561.04(1)(a) shall ensure that any person who performs work under a manufacturer certificate complies with the manual.
(3) [Repealed, SOR/2019-295, s. 10]
(4) Subject to the following conditions, the holder of a manufacturer certificate and any person who performs work under a manufacturer certificate may temporarily be authorized to use alternative policies and procedures to comply with subsections (2) and (3):
(a) they have determined that, as a result of unforeseen or temporary circumstances, compliance with the manual would be impossible or unreasonable;
(b) they believe on reasonable grounds that the safety of the aeronautical product can be achieved by complying with the alternative policies and procedures;
(c) they have notified the Minister in writing; and
(d) the Minister has notified them in writing that they can use those alternative policies and procedures.
(5) The holder of a manufacturer certificate shall submit the manual and any subsequent amendment to the Minister for approval.
(6) The Minister shall approve the manual and any subsequent amendment if they meet the requirements of this Subpart and Standard 561.
(7) If the manual no longer meets the requirements of this Subpart or Standard 561, the holder of a manufacturer certificate shall
(8) The person who has been assigned the responsibility under subsection 561.04(6) shall amend each copy of the manual within 30 days after receiving the Minister’s approval of an amendment to it.
(9) A manual may incorporate other documents by reference if it includes policies and procedures to control the incorporated material.
(10) The person appointed under paragraph 561.04(1)(a) shall ensure that any part of the manual or incorporated document that is relevant to the work to be performed is made available to each person who performs that work.
- SOR/2005-348, s. 4
- SOR/2015-160, s. 25(F)
- SOR/2019-295, s. 10
Production Control System
561.08 (1) The holder of a manufacturer certificate shall establish and maintain a production control system that consists of systems and procedures set out in section 561.08 of Standard 561 to ensure that aeronautical products comply with these Regulations throughout the manufacturing process.
(2) The production control system shall be under the control of
(a) the person appointed under paragraph 561.04(1)(a); or
(b) a person assigned the responsibility for the management of the production control system under subsection 561.04(6).
(3) The person referred to in subsection (2) who has control of the production control system shall ensure that the activities carried out under the manufacturer certificate for which they have been assigned responsibility are in compliance with this Subpart.
- SOR/2005-348, s. 4
Quality Assurance Program
561.09 (1) The holder of a manufacturer certificate shall, in order to ensure that all aspects of the activities carried out under the manufacturer certificate continue to comply with these Regulations, establish and maintain a quality assurance program, independent of the production control system, that
(2) The person referred to in paragraph (1)(a) shall ensure that records related to the findings from the quality assurance program are distributed to the appropriate manager for corrective action and follow-up in accordance with the procedures specified in the manual.
(3) The person referred to in paragraph (1)(a) shall establish and maintain an audit system that consists of
(a) an initial audit, within 12 months after the day on which the manufacturer certificate is issued, that covers all aspects of the manufacturer’s activities;
(b) subsequent audits conducted at the intervals set out in the manual;
(c) a record of each occurrence of compliance or non-compliance found during an audit referred to in paragraph (a) or (b);
(d) procedures for ensuring that each finding of an audit is communicated to them;
(e) follow-up procedures for ensuring that corrective actions are effective; and
(f) a system for recording the findings of initial and periodic audits, corrective actions and follow-ups.
(4) The records required under paragraph (3)(f) shall be retained for the greater of
(5) The quality assurance program duties related to specific tasks or activities shall be performed by persons who are not responsible for and have not been involved in the performance of the tasks or activities being audited.
- SOR/2005-348, s. 4
Statement of Conformity
561.10 (1) No person shall sign a statement of conformity in respect of an aeronautical product unless
(a) the statement contains the elements referred to in section 561.10 of Standard 561;
(b) the person has been authorized to do so by the person in control of the production control system;
(c) the aeronautical product is specified in the manufacturer certificate; and
(d) the aeronautical product has been manufactured in accordance with this Subpart.
(2) No person shall authorize a person to sign, on behalf of the holder of a manufacturer certificate, a statement of conformity unless the person being authorized has complied with the policies and procedures set out in the manual and has successfully completed the training required under section 561.11.
- SOR/2005-348, s. 4
Training Program
561.11 The holder of a manufacturer certificate shall
(a) establish and maintain a training program that includes the initial training, updating and any other training set out in section 561.11 of Standard 561 to ensure continued qualification that is appropriate to the function to be performed or supervised; and
(b) ensure that persons who are authorized to perform or supervise the performance of any function required under this Subpart are trained in respect of the parts of the policies and procedures of the holder of the manufacturer certificate and the parts of these Regulations applicable to that function.
- SOR/2005-348, s. 4
Personnel Records
561.12 (1) The holder of a manufacturer certificate shall establish and maintain a personnel record for each employee of the manufacturer and retain each record for at least three years after the end of their employment.
(2) A personnel record may be in paper or electronic form and shall include all of the employee’s qualifications, all authorizations to sign a statement of conformity pursuant to section 561.10 and a description of the training referred to in section 561.11.
(3) The holder of a manufacturer certificate shall ensure that a copy of any record required by this section is provided to the employee referred to in the record on the completion of each training activity or the granting of an authorization to sign a statement of conformity under section 561.10.
- SOR/2005-348, s. 4
Control of Suppliers
561.13 (1) The holder of a manufacturer certificate who contracts work to a supplier shall ensure that
(a) a written agreement with the supplier specifies the work to be performed by the supplier and provides that the Minister may have access to and inspect the supplier’s facilities and records to ensure compliance with this Subpart;
(b) work is contracted only to suppliers that have been evaluated in accordance with the policies and procedures set out in the manual;
(c) work is done under the holder’s supervision and is subject to the quality assurance program set out in section 561.09;
(d) the supplier’s capability to perform the contracted work is evaluated and monitored; and
(e) the aeronautical product conforms to its approved design.
(2) If a supplier holds, in respect of an aeronautical product, a manufacturer certificate or an equivalent document issued by a foreign state with which Canada has an airworthiness agreement or similar arrangement, the issuance of the supplier’s own statement of conformity in respect of that product is considered as meeting the requirements of paragraphs (1)(c) to (e).
(3) No supplier who performs work for a holder of a manufacturer certificate under this Subpart shall subcontract the work to another supplier without having first obtained the written consent of the holder of a manufacturer certificate.
- SOR/2005-348, s. 4
Aeronautical Product Records
561.14 (1) The holder of a manufacturer certificate shall establish and maintain records for each aeronautical product manufactured under a manufacturer certificate, including those specified in section 561.14 of Standard 561.
(2) The holder of a manufacturer certificate shall ensure that product records are kept for at least three years after the day on which the statement of conformity was signed.
- SOR/2005-348, s. 4
Service Difficulty Reporting
561.15 The holder of a manufacturer certificate shall report to the Minister, in accordance with Division IX of Subpart 21 of Part V, any reportable service difficulty related to an aeronautical product being manufactured.
- SOR/2005-348, s. 4
- SOR/2009-280, s. 29
Cessation of Manufacturing
561.16 The holder of a manufacturer certificate shall notify the Minister in writing of the permanent cessation of the manufacture of an aeronautical product specified in the manufacturer certificate within 30 days after cessation.
- SOR/2005-348, s. 4
Subpart 71 — Aircraft Maintenance Requirements
Application
571.01 This Subpart applies in respect of maintenance and elementary work performed on the following aircraft, except for remotely piloted aircraft that are an element of a remotely piloted aircraft system in respect of which a design approval document has not been issued or applied for under Subpart 21 of this Part, ultra-light aeroplanes and hang gliders:
(a) Canadian aircraft;
(b) foreign aircraft operated under Part IV or VII;
(c) foreign aircraft, other than aircraft referred to in paragraph (b), if the maintenance or elementary work is performed under the terms of an agreement or technical arrangement between Canada and the state of registry of the aircraft; and
(d) parts intended for installation on aircraft referred to in paragraphs (a) to (c).
- SOR/2000-404, s. 3
- SOR/2019-11, s. 14
- SOR/2025-70, s. 40
Maintenance and Elementary Work Performance Rules
571.02 (1) Subject to subsection (2), a person who performs maintenance or elementary work on an aeronautical product shall use the most recent methods, techniques, practices, parts, materials, tools, equipment and test apparatuses that are
(a) specified for the aeronautical product in the most recent maintenance manual or instructions for continued airworthiness developed by the manufacturer of that aeronautical product;
(b) equivalent to those specified by the manufacturer of that aeronautical product in the most recent maintenance manual or instructions for continued airworthiness; or
(c) in accordance with recognized industry practices at the time the maintenance or elementary work is performed.
(2) A person who performs maintenance or elementary work pursuant to subsection (1) shall ensure that any measuring device or test equipment used
(a) meets the specifications of the manufacturer of the aeronautical product with respect to accuracy, taking into account the intended use; and
(b) if calibration requirements are published by the manufacturer of the measuring device or test equipment, is calibrated by means traceable to a national standard.
(3) Except if the work is performed in respect of an aircraft that is operated under a special certificate of airworthiness in the owner-maintenance or amateur-built classification, no person shall supervise, or perform without supervision, an inspection using a method set out in column I of an item of Schedule I to this Subpart unless the person holds the personnel certification set out in column II of that item.
- SOR/2002-112, s. 4
- SOR/2003-122, s. 1
Recording of Maintenance and Elementary Work
571.03 A person who performs maintenance or elementary work on an aeronautical product shall ensure that
(a) the details required by Standard 571 — Maintenance are entered in the technical record for the aeronautical product, in respect of the task performed; and
(b) the technical record is accurate with respect to any outstanding elements of the work performed, in particular, the need to secure any fastening device that was disturbed to facilitate the work.
- SOR/2019-122, s. 21
Specialized Maintenance
571.04 No person shall perform the specialized maintenance set out in Schedule II to this Subpart on an aeronautical product other than an aircraft operated under a special certificate of airworthiness in the owner-maintenance or amateur-built classification, except in accordance with
(a) a maintenance policy manual (MPM) established by the holder of an approved maintenance organization (AMO) certificate issued pursuant to section 573.02 with a rating of a category appropriate to the work to be performed; or
(b) a foreign document equivalent to an MPM established by a maintenance organization approved under the laws of a state that is party to an agreement with Canada, and the agreement provides for recognition of the work to be performed.
- SOR/2002-112, s. 5
Maintenance of Aircraft Operated under Part IV or VII
571.05 Except in the case of a balloon, no person shall perform maintenance on an aircraft operated under Part IV or VII, or install on one of the foregoing a part that has undergone maintenance, unless the maintenance on that aircraft or part has been performed in accordance with
(a) a maintenance policy manual (MPM) established by the holder of an approved maintenance organization (AMO) certificate issued pursuant to section 573.02 with a rating of a category appropriate to the work to be performed; or
(b) a foreign document equivalent to an MPM established by a maintenance organization approved under the laws of a state that is party to an agreement with Canada and the agreement provides for recognition of the work to be performed.
- SOR/2000-404, s. 6
Repairs and Modifications
571.06 (1) Except as provided in subsection (5) and in the case of aircraft that are operated under a special certificate of airworthiness in the owner-maintenance classification, a person who signs a maintenance release in respect of a major repair or major modification on an aeronautical product shall ensure that the major repair or major modification conforms to the requirements of the relevant technical data
(2) Except as provided in subsection (5), a person who signs a maintenance release in respect of a repair or modification, other than a major repair or major modification, shall ensure that the repair or modification conforms to the requirements of the relevant technical data within the meaning of the term acceptable data in section 571.06 of the Airworthiness Manual.
(3) Where an additional flight authority has been issued under paragraph 507.08(1)(b) in respect of an aircraft, no person shall change the configuration of the aircraft in such a manner that the aircraft no longer meets the conditions subject to which the flight authority applicable to the aircraft prior to the modification was issued, unless
(4) Repairing or modifying an aeronautical product may include the making of a part in conformity with the standards specified in section 571.06 of the Airworthiness Manual, if no part made is
(5) A person who signs a maintenance release in respect of a repair or modification performed on a foreign aeronautical product under the terms of an agreement or a technical arrangement between Canada and the aircraft’s state of registry shall ensure that the repair or modification conforms to the requirements of the relevant technical data that are specified in the agreement or technical arrangement.
- SOR/2000-404, s. 7
- SOR/2002-112, s. 6
- SOR/2003-122, s. 2
- SOR/2025-26, s. 22
Installation of New Parts
571.07 (1) No person shall install a new part on an aeronautical product unless the part meets the standards of airworthiness applicable to the installation of new parts and, subject to subsections (2) and (3), has been certified under Subpart 61.
(2) No certification referred to in subsection (1) is required where
(a) a new part is a foreign-manufactured part that is certified pursuant to an agreement with Canada, which agreement provides for the acceptance of export airworthiness certification;
(b) a new part is a foreign-manufactured part that is obtained from a manufacturer holding a type design recognized in Canada and the part is certified in accordance with the laws of the state of manufacture;
(c) a new part, whose accompanying documentation has been verified, has been inspected in accordance with the requirements of Standard 571 — Maintenance;
(d) a new part is installed on an aircraft that is operated under a special certificate of airworthiness in the owner-maintenance or amateur-built classification; or
(3) No certification referred to in subsection (1) is required in respect of a new part that bears markings identifying it as a part specified in the type design and that
- SOR/2002-112, s. 7
- SOR/2005-348, s. 5
- SOR/2009-280, s. 30
- SOR/2019-122, s. 21
Installation of Used Parts
571.08 (1) No person shall install a used part on an aeronautical product, other than aircraft that are operated under a special certificate of airworthiness in the owner-maintenance or amateur-built classification, unless the part meets the standards of airworthiness that are applicable to the installation of used parts and are set out in Standard 571 — Maintenance and
(a) is an airworthy part that has been removed from an aircraft for immediate installation on another aircraft;
(b) is an airworthy part that has undergone maintenance for which a maintenance release has been signed pursuant to paragraph 571.11(2)(c); or
(c) has been inspected and tested to ensure that the part conforms to its type design and is in a safe condition, and a maintenance release has been signed to that effect.
(2) If, under the terms of a loan agreement or an air operator parts pooling agreement, a used part has been obtained from a source not subject to these Regulations, no person shall permit the part to remain in service for longer than 90 days unless specifically authorized by the Minister on receipt of documentation demonstrating that the part conforms to the applicable type design.
- SOR/2002-112, s. 8
- SOR/2019-122, s. 21
Installation and Disposal of Life-limited Parts
571.09 (1) No person shall install a used life-limited part on an aeronautical product unless the part meets the standards of airworthiness applicable to the installation of life-limited parts and
(a) the technical history of the part within the meaning of section 571.09 of the Airworthiness Manual is available to show that the time in service authorized for that part in the type certificate governing the installation has not been exceeded; and
(b) the history referred to in paragraph (a) is incorporated into the technical record for the aeronautical product on which the part is installed.
(2) No person shall install a used life-limited part in a place other than that from which it was removed unless the part is installed
(a) in the same or in an identical position on another aeronautical product bearing the same part number as that from which the part was removed; or
(b) in conformity with the requirements in respect of technical data that have been approved or the use of which has been approved within the meaning of section 571.09 of the Airworthiness Manual.
(3) When a life-limited part has reached the time in service authorized in its type design, the part shall be
- SOR/2002-112, s. 10
Maintenance Release
571.10 (1) No person shall sign a maintenance release required pursuant to section 605.85 or permit anyone whom the person supervises to sign a maintenance release, unless the standards of airworthiness applicable to the maintenance performed and stated in Standard 571 — Maintenance have been complied with and the maintenance release meets the applicable requirements specified in section 571.10 of the Airworthiness Manual.
(2) Except as provided in subsection (4), a maintenance release shall include the following, or a similarly worded, statement:
“The described maintenance has been performed in accordance with the applicable airworthiness requirements.”
(3) No maintenance release is required in respect of any task designated as elementary work in the Aircraft Equipment and Maintenance Standards that is performed by
(a) in the case of a glider, a balloon or an unpressurized small aircraft that is powered by a piston engine and not operated pursuant to Part IV or VII, the pilot of the aircraft;
(b) in the case of an aircraft operated under Part IV or VII, a person who has been trained and authorized in accordance with the flight training unit’s or the air operator’s maintenance control manual (MCM), approved under Subpart 6 of Part IV or of Part VII, respectively; or
(c) in the case of an aircraft operated pursuant to Subpart 4 of Part VI, a person who has been trained in accordance with those sections of a private operator’s operations manual that contain details of the operator’s maintenance control system.
(4) Where a person signs a maintenance release in respect of maintenance performed on an aircraft, the satisfactory completion of which cannot be verified by inspection or testing of the aircraft on the ground, the maintenance release shall be made conditional on the satisfactory completion of a test flight carried out pursuant to subsections 605.85(2) and (3), by the inclusion of the phrase “subject to satisfactory test flight”.
(5) No person shall sign a maintenance release in respect of specialized maintenance unless the requirements of section 571.04 have been met.
- SOR/2000-404, s. 8
- SOR/2003-154, s. 6(F)
- SOR/2019-122, s. 21
Persons Who May Sign a Maintenance Release
571.11 (1) Except as provided in subsections (2) and (7), no person other than the holder of an aircraft maintenance engineer (AME) licence issued under Part IV, specifying a rating appropriate to the aeronautical product being maintained, shall sign a maintenance release as required by section 571.10.
(2) A person other than a person described in subsection (1) may sign a maintenance release if
(a) in the case of maintenance performed outside Canada,
(i) the person is authorized to sign under the laws of a state that is party to an agreement or a technical arrangement with Canada and the agreement or technical arrangement provides for such certification, or
(ii) if no agreement or technical arrangement provides for such certification, the person holds qualifications that the Minister determines to be equivalent to those of a person described in subsection (1);
(b) in the case of maintenance performed on an aircraft that is operated under a special certificate of airworthiness in the amateur-built classification, the person is an owner of the aircraft;
(c) in the case of maintenance performed on a part that is intended for installation on an aircraft, the person has been authorized to sign by the holder of an approved maintenance organization (AMO) certificate issued under section 573.02; and
(d) in the case of maintenance performed on an aircraft that is operated under a special certificate of airworthiness in the owner-maintenance classification, the person is a licensed pilot and an owner of the aircraft.
(3) Except as provided in subsection (7), no person shall sign a maintenance release in respect of maintenance performed on an aircraft operated under Part IV or VII, or on parts intended to be installed on the aircraft, unless
(a) the person is authorized to sign in accordance with a maintenance policy manual (MPM) established by the holder of an AMO certificate issued under section 573.02 with a rating of a category appropriate to the work performed; or
(b) if the maintenance is performed outside Canada, the person is authorized to sign in accordance with a foreign document equivalent to an MPM, established by a maintenance organization approved under the laws of a state that is party to an agreement or technical arrangement with Canada and the agreement or technical arrangement provides for such certification.
(4) Except as provided in subsections (5) and (7), no person shall sign a maintenance release in respect of maintenance performed on a transport category aeroplane or a turbine-powered helicopter, unless the person
(a) has successfully completed a course of maintenance training that has been approved by the Minister and that is applicable to the type of aircraft, engine or system on which the maintenance is performed, in accordance with Appendix M of Standard 571 — Maintenance; or
(b) held a type rating applicable to the type of aircraft, engine or system on which the maintenance is performed, issued by the Minister before August 1, 1999.
(5) The holder of an applicable AME licence may sign a maintenance release in respect of maintenance performed on a transport category aeroplane or a turbine-powered helicopter that consists of any of the types of work set out in Schedule III without having successfully completed the course required by paragraph (4)(a) and without having held the type rating required by paragraph (4)(b).
(6) If a maintenance release is signed by a person in respect of work performed by another person, the person signing the maintenance release must personally observe the work to the extent necessary to ensure that it is performed in accordance with the requirements of any applicable standards of airworthiness and, specifically, the requirements of sections 571.02 and 571.10.
(7) A person who is not the holder of an AME licence specifying a rating appropriate to the aeronautical product being maintained may sign a maintenance release if the person holds a restricted certification authority issued in accordance with subsection (8), in respect of a particular case specified on the restricted certification authority.
(8) The Minister shall issue a restricted certification authority and specify therein its validity period and the scope of the work that may be performed, if
(a) an application is made in accordance with section 571.11 of the Airworthiness Manual;
(b) the applicant demonstrates to the Minister that there is no holder of an AME licence specifying a rating appropriate to the aeronautical product being maintained available within a geographical area accessible within one hour by surface transportation;
(c) the person to whom the restricted certification authority is to be issued has received the training and has the knowledge equivalent to that of a holder of an AME licence specifying a rating appropriate to the aeronautical product being maintained; and
(d) the level of aviation safety is not affected by the issuance of the restricted certification authority.
- SOR/2000-404, s. 9
- SOR/2002-112, s.11
- SOR/2019-122, s. 3
Reporting Major Repairs and Major Modifications
571.12 A person who performs a major repair or major modification on an aeronautical product or installs on an aircraft a part that has undergone a major repair or major modification shall report the action to the Minister in accordance with the procedures specified in section 571.12 of the Airworthiness Manual.
Installation of Parts (General)
571.13 (1) Subject to sections 571.07 to 571.09, no person shall install a part on an aeronautical product unless the part is
(2) If a part is obtained from an aeronautical product that was damaged or permanently withdrawn from service, the part shall not be installed unless it
(a) can be traced to the manufacturer certificate holder; and
(b) is inspected in conformity with the instructions for continued airworthiness or, if the part has been repaired or modified, it can be ascertained that the work was performed in accordance with approved data within the meaning of section 571.06 of the Airworthiness Manual.
- SOR/2002-112, s. 12
Subpart 73 — Approved Maintenance Organizations
Division I — General
Application for Approval
573.01 (1) An applicant for an approved maintenance organization (AMO) certificate or for an amendment of an AMO certificate that is in effect shall make an application in the form and manner specified in Standard 573 —Approved Maintenance Organizations.
(2) An applicant referred to in subsection (1) shall submit to the Minister with the application a copy of its maintenance policy manual (MPM) required pursuant to subsection 573.10(1).
- SOR/2005-173, s. 28
Entitlement to and Scope of Certificate
573.02 (1) The Minister shall issue to a maintenance organization that demonstrates that it meets the requirements of this Subpart an approved maintenance organization (AMO) certificate authorizing the maintenance of specified aeronautical products or the provision of specified maintenance services.
(2) The AMO certificate shall specify, in accordance with the criteria specified in section 573.02 of Standard 573 — Approved Maintenance Organizations, any category in which ratings have been issued and shall list the aeronautical products that the AMO is authorized to maintain or the maintenance services that the AMO is authorized to perform.
(3) The scope of the work that may be performed under each rating specified on the AMO certificate is determined by limitations that are set out in the certificate.
(4) Unless an expiry date is specified in an AMO certificate issued pursuant to subsection (1), the certificate remains in effect until it is surrendered, suspended or cancelled.
- SOR/2005-173, s. 15
Duties of Certificate Holder
573.03 (1) The holder of an approved maintenance organization (AMO) certificate shall
(a) appoint a person responsible for maintenance;
(b) ensure that the person responsible for maintenance meets the requirement set out in subsection 573.04(1);
(c) subject to subsection (4), ensure that the person responsible for maintenance
(d) [Repealed, SOR/2022-246, s. 13]
(e) ensure that the person responsible for maintenance performs the duties referred to in subsections 573.04(3) and 573.09(2) and (3);
(f) provide the person responsible for maintenance with the financial and human resources necessary to ensure that the holder of the AMO certificate meets the requirements of these Regulations;
(g) ensure that corrective actions are taken in respect of any findings resulting from a quality assurance program established under subsection 573.09(1) or a safety management system referred to in section 573.30; and
(h) conduct reviews of the safety management system to determine its effectiveness.
(2) [Repealed, SOR/2022-246, s. 13]
(3) [Repealed, SOR/2022-246, s. 13]
(4) The knowledge requirement set out in subparagraph (1)(c)(i) does not apply in respect of
(5) The experience requirement set out in subsection 573.04(1) of Standard 573 — Approved Maintenance Organizations does not apply in the case of an AMO certificate in respect of which no rating in the aircraft, avionics, instrument, engine or propeller category has been issued if the accountable executive can demonstrate to the Minister by means of a risk assessment that the lesser experience is appropriate to the scope of work performed by the AMO and will not affect aviation safety or the safety of the public.
(6) The holder of an AMO certificate shall ensure that no person is appointed to be responsible for maintenance or remains responsible for maintenance if, at the time of their appointment or during their tenure, they have a record of conviction for
(7) The holder of a certificate referred to in subsection (1) shall ensure that the person managing the safety management system who is referred to in section 573.32 performs the duties set out in that section.
- SOR/2005-173, s. 16
- SOR/2005-357, s. 5
- SOR/2019-295, s. 11
- SOR/2022-246, s. 13
Person Responsible for Maintenance
573.04 (1) The person responsible for maintenance shall, within 30 days after their appointment under paragraph 573.03(1)(a), submit to the Minister a signed statement that they accept the responsibilities of their position.
(2) [Repealed, SOR/2019-295, s. 12]
(3) The person responsible for maintenance shall, where a finding resulting from a quality assurance program established under subsection 573.09(1) or a safety management system referred to in section 573.30 is reported to them,
(a) determine what, if any, corrective actions are required and carry out those actions;
(b) keep a record of any determination made under paragraph (a) and the reason for it;
(c) if management functions have been assigned to another person under subsection (4) or (5), communicate any determination regarding a corrective action to that person; and
(d) notify the accountable executive of any systemic deficiency and of the corrective action taken.
(4) The person responsible for maintenance may assign the management functions for the entire quality assurance program established under subsection 573.09(1) or for the safety management system referred to in 573.30 to another person if
(a) that person meets the requirements set out in paragraph 573.03(1)(c) and subsection 573.03(6); and
(b) the assignment and its scope are described in the AMO’s MPM.
(5) The person responsible for maintenance may assign the management functions for specific maintenance activities to another person if the assignment and its scope are described in the AMO’s MPM.
(6) The responsibility of the person responsible for maintenance is not affected by the assignment to another person of management functions under subsection (4) or (5).
- SOR/2005-173, s. 16
- SOR/2019-295, s. 12
- SOR/2022-246, s. 14
Authorization to Sign a Maintenance Release
573.05 (1) No approved maintenance organization (AMO) certificate holder shall authorize a person to sign a maintenance release unless the person meets the applicable requirements of section 571.11 and has successfully completed the training required by section 573.06.
(2) No AMO certificate holder shall authorize a person to sign a maintenance release under paragraph 571.11(2)(c) unless the person has, in respect of the work being certified, demonstrated to the certificate holder levels of knowledge and experience that are appropriate and that meet the applicable criteria set out in section 573.05 of Standard 573 — Approved Maintenance Organizations.
- SOR/2005-173, s. 17
Training Program
573.06 (1) An approved maintenance organization (AMO) certificate holder shall implement a training program to ensure that persons authorized to perform or supervise the performance of any function under this Subpart are trained in respect of the regulations, the standards and the AMO procedures applicable to that function.
(2) The program required by subsection (1) shall include initial training, updating and any other training necessary, within the meaning assigned to those terms in section 573.06 of Standard 573 — Approved Maintenance Organizations, to ensure continued qualification that is appropriate to the function to be performed or supervised.
- SOR/2005-173, s. 18
Personnel Records
573.07 (1) An approved maintenance organization (AMO) certificate holder shall establish, maintain and retain for at least two years after an entry is made, for each affected person, a record of
(a) all personal qualifications in respect of appointments made pursuant to section 573.03 and in respect of assignments of functions made pursuant to section 573.04;
(b) all of the authorizations to sign a maintenance release pursuant to section 573.05; and
(c) all of the training conducted pursuant to section 573.06.
(2) An AMO certificate holder shall provide a copy of a record required by this section to the person to whom the record refers on the completion of each training activity or the granting of an authorization referred to in paragraph (1)(b).
Facilities, Equipment, Standards and Procedures
573.08 (1) An approved maintenance organization (AMO) certificate holder shall provide the facilities and equipment specified in Standard 573 —Approved Maintenance Organizations that are necessary for the work to be performed.
(2) Except in cases provided for in a maintenance policy manual (MPM), work performed by an AMO certificate holder shall be performed in the facilities required by subsection (1), unless unforeseen circumstances do not permit the work to be performed in those facilities and the safety of the aircraft is not affected by the fact that the work is performed elsewhere.
(3) Where an AMO uses standards equivalent to those of the manufacturer of an aeronautical product for the performance of work pursuant to paragraph 571.02(1)(b), those standards shall be identified in accordance with section 573.10.
(4) Where a task undertaken by an AMO is divided into sub-tasks, the person appointed pursuant to section 573.03 shall establish a system of task control to ensure that all of the sub-tasks are completed prior to the signing of a maintenance release in respect of the completion of that task.
- SOR/2005-173, s. 28
Quality Assurance Program
573.09 (1) The holder of an approved maintenance organization (AMO) certificate shall establish and maintain a quality assurance program consisting of provisions for sampling maintenance processes to evaluate the AMO’s ability to perform its maintenance in a safe manner.
(2) The person responsible for maintenance shall ensure that records relating to the findings resulting from the quality assurance program are distributed to the appropriate manager for corrective action and follow-up in accordance with the policies and procedures specified in the maintenance policy manual (MPM).
(3) The person responsible for maintenance shall establish an audit system in respect of the quality assurance program that consists of the following:
(a) an initial audit within 12 months after the date on which the AMO certificate is issued;
(b) subsequent audits conducted at intervals set out in the MPM;
(c) checklists of all activities controlled by the MPM;
(d) a record of each occurrence of compliance or non-compliance with the MPM found during an audit referred to in paragraph (a) or (b);
(e) procedures for ensuring that each finding of an audit is communicated to them and, if management functions have been assigned to another person under subsection 573.04(4) or (5), to that person;
(f) follow-up procedures for ensuring that corrective actions are effective; and
(g) a system for recording the findings of initial and periodic audits, corrective actions and follow-ups.
(4) The records required under paragraph (3)(g) shall be retained for the greater of
(5) The duties related to the quality assurance program that involve specific tasks or activities within an AMO’s activities shall be fulfilled by persons who are not responsible for carrying out those tasks or activities.
- SOR/2005-173, s. 19
Maintenance Policy Manual
573.10 (1) An approved maintenance organization (AMO) certificate holder shall establish, maintain and authorize the use of a maintenance policy manual (MPM) that contains information to ensure the efficiency of the AMO’s maintenance policies, dealing with the subjects set out in Standard 573 —Approved Maintenance Organizations.
(2) The Minister may authorize the incorporation by reference in an MPM of detailed procedures manuals and lists prepared by the AMO certificate holder, dealing with the subjects set out in Standard 573 —Approved Maintenance Organizations, where
(3) Where detailed procedures manuals or lists are being incorporated by reference in an MPM, the person appointed pursuant to section 573.03 or another person to whom that management function is assigned pursuant to section 573.04 shall certify in writing that the incorporated documents and every amendment thereto meet the requirements of the policy established in the MPM with respect to those documents.
(4) An AMO certificate holder need not conform to the policy and procedures contained in its MPM, where the Minister has authorized the non-conformity in writing, after it has been demonstrated that such non-conformity would not affect the safety of the aeronautical product to be maintained or the maintenance service to be offered.
(5) An AMO certificate holder shall submit each page of its MPM to the Minister for approval, either individually or in accordance with a procedure that ensures compliance with the requirements of Standard 573 —Approved Maintenance Organizations.
(6) An AMO certificate holder shall amend its MPM when instructed to do so by the Minister, where the MPM does not
(7) An AMO certificate holder shall take steps to ensure that a current copy of its MPM, or the portions thereof that are relevant to the task to be performed, is made available to each person who performs or certifies that task.
(8) An AMO certificate holder shall amend each copy of its MPM within 30 days after receiving an approval issued pursuant to subsection (5).
(9) The Minister shall, if the standards set out in Standard 573 —Approved Maintenance Organizations are met, approve an MPM and any amendments to that manual.
- SOR/2000-404, s. 12
- SOR/2005-173, s. 28
Maintenance Arrangements
573.11 (1) Except as provided in subsection (2), no approved maintenance organization (AMO) certificate holder shall permit an external agent to perform maintenance on its behalf unless
(a) the external agent holds an AMO certificate with a rating of a category specified pursuant to section 573.02 that is appropriate to the type of work to be performed or the aeronautical product to be maintained;
(b) where the work is to be performed outside Canada, the external agent has been authorized to do the type of work to be performed or to perform maintenance on the type of aeronautical product to be maintained under the laws of a state that is party to an agreement with Canada and the agreement provides for the recognition of maintenance functions; or
(c) in all other cases, the performance of the maintenance by the person or organization has been approved by the Minister as being in conformity with these Regulations.
(2) Subject to subsection (4), an AMO certificate holder may permit work to be performed by an external agent other than an agent described in subsection (1) where the work is performed in accordance with an arrangement that provides for it, under the direct supervision of the person appointed pursuant to section 573.03 or 573.04 and certified by persons authorized to do so in accordance with the approved procedures set out in the AMO’s maintenance policy manual (MPM).
(3) Arrangements respecting work to be performed by external agents pursuant to subsection (2) shall be made in accordance with procedures governing maintenance arrangements set out in the MPM or, if no such procedures are set out in the MPM, shall be approved by the Minister as ensuring conformity with the requirements of this Subpart.
(4) An AMO certificate holder that requests an external agent to perform work shall
(a) where the work is to be performed pursuant to subsection (1) or (2), be responsible for specifying the tasks to be performed by the agent and ensuring completion of the work; and
(b) where the work is to be performed pursuant to subsection (2), be responsible for ensuring the conformity of that work with the requirements of Subpart 71.
(5) A maintenance arrangement that is made by a foreign air operator to have its maintenance done in Canada by a person or organization that holds an AMO certificate issued pursuant to section 573.02 shall be authorized by a maintenance specification issued to the AMO in accordance with the requirements of Standard 573 — Approved Maintenance Organizations, where the air operator is from a state that
(a) is party to an agreement with Canada that provides for recognition of the work performed and the issuance of a maintenance specification is specified in the agreement; or
(b) is not party to an agreement with Canada that provides for recognition of the work performed and the issuance of a maintenance specification is requested by that state.
- SOR/2005-173, s.28
Service Difficulty Reporting
573.12 The holder of an approved maintenance organization (AMO) certificate shall report to the Minister, in accordance with Division IX of Subpart 21 of Part V, any reportable service difficulty related to an aeronautical product being maintained.
- SOR/2009-280, s. 32
Foreign Approvals
573.13 An application submitted by a maintenance organization for the issuance or amendment of an approved maintenance organization (AMO) certificate authorizing the performance of work in facilities located outside Canada is granted if
(a) the applicant has demonstrated that the issuance of the approval in respect of those facilities is in the public interest as provided for in subsection 6.71(1) of the Act;
(b) the applicant has recognized by advance agreement the Minister’s right to enter and inspect those facilities and seize anything found in those facilities, under the same conditions as would govern the exercise of the Minister’s powers pursuant to subsection 8.7(1) of the Act if the facilities were located in Canada;
(c) the AMO has agreed to reimburse the Minister for any expenses incurred by Department of Transport personnel in carrying out the activities provided for in paragraph (b) in respect of those facilities; and
(d) in the case of an AMO whose facilities are located outside Canada, the Minister specifies on the AMO certificate the date on which the certificate expires.
Identification of an AMO
573.14 (1) No person, other than the holder of an approved maintenance organization (AMO) certificate issued in accordance with this Subpart, shall identify oneself as an AMO certificate holder.
(2) A person who holds an AMO certificate issued in accordance with this Subpart shall not include, in a list of approved maintenance services offered for aeronautical products, a service that is outside the scope of the person’s AMO certificate.
Technical Records
573.15 An approved maintenance organization (AMO) certificate holder shall maintain records in accordance with section 573.15 of Standard 573 — Approved Maintenance Organizations for work performed on all aeronautical products maintained and keep those records for at least two years beginning on the date that the maintenance release was signed.
- SOR/2003-122, s. 4
Division II — Safety Management System
Requirements
573.30 The safety management system required under section 107.02 in respect of an applicant for, or a holder of, an approved maintenance organization (AMO) certificate authorizing the holder to perform maintenance on an aircraft operated under Subpart 5 of Part VII shall
(a) meet the requirements of Subpart 7 of Part I and section 573.31; and
(b) be under the control of the person responsible for maintenance appointed under paragraph 573.03(1)(a).
- SOR/2005-173, s. 20
Components of the Safety Management System
573.31 (1) The safety management system shall include, among others, the following components:
(a) a safety management plan that includes
(i) a safety policy that the accountable executive has approved and communicated to all employees,
(ii) the roles and responsibilities of personnel assigned duties under the quality assurance program established under subsection 573.09(1) or the safety management system,
(iii) performance goals and a means of measuring attainment of those goals,
(iv) a policy for the internal reporting of a hazard, an incident or an accident, including the conditions under which immunity from disciplinary action will be granted, and
(v) a review of the safety management system to determine its effectiveness;
(b) procedures for reporting a hazard, an incident or an accident to the appropriate manager;
(c) procedures for the collection of data relating to hazards, incidents and accidents;
(d) procedures for analysing data obtained under paragraph (c) and during an audit conducted under subsection 573.09(3) and for taking corrective actions;
(f) training requirements for the person responsible for maintenance and for personnel assigned duties under the safety management system; and
(g) procedures for making progress reports to the accountable executive at intervals determined by the accountable executive and other reports as needed in urgent cases.
(2) The components specified in subsection (1) shall be set out in the approved maintenance organization (AMO) certificate holder’s maintenance policy manual (MPM).
- SOR/2005-173, s. 20
Person Managing the Safety Management System
573.32 The person managing the safety management system in respect of an approved maintenance organization (AMO) shall
(a) establish and maintain a reporting system to ensure the timely collection of information related to hazards, incidents and accidents that may adversely affect safety;
(b) identify hazards and carry out risk management analyses of those hazards;
(c) investigate, analyze and identify the cause or probable cause of all hazards, incidents and accidents identified under the safety management system;
(d) establish and maintain a safety data system, by either electronic or other means, to monitor and analyze trends in hazards, incidents and accidents;
(e) monitor and evaluate the results of corrective actions with respect to hazards, incidents and accidents;
(f) monitor the concerns of the civil aviation industry in respect of safety and their perceived effect on the AMO;
(g) determine the adequacy of the training required by paragraph 573.31(1)(f); and
(h) where the person responsible for maintenance has assigned the management functions for the safety management system under subsection 573.04(4) to another person, report to the person responsible for maintenance the hazards, incidents and accidents identified under the safety management system required under section 573.30 or as a result of an audit required under paragraph 573.31(1)(e).
- SOR/2005-173, s. 20